AAON LZ Series Скачать руководство пользователя | Manualshive

Страница: 68 / 104

background image

68

Bearings - Lubrication

Every  6  months  or  after  a  prolonged  shut
down. Use waterproof, lithium based grease.
Below  32°F  -  Esso  Exxon  or  Beacon  325.
Above  32°F  -  Mobil  Mobilox  EP2,  Shell
Alvania EP2, or Texaco RB2.

Recommended Monthly Inspection

1.

Clean  sump  section  interior.  Dirt  and
other impurities which have accumulated
in the sump should be removed from the
sump  area.  Shut  off  makeup  water  ball
valve  and  open  the  drain  connection  for
flushing of the sump.

2.

Clean dirt out of sump using a water hose
(not a pressure washer).

3.

Clean sump suction strainer.

4.

Check water operating level. Adjust float
as required.

5.

Inspect fan motor(s) and water circulation
pump(s) and lubricate per the lubrication
nameplate

or

manufacture’s

recommendations.

6.

Inspect axial fans and eliminators
removing any debris which may have
accumulated during operation.

7.

Inspect the water distribution system to
insure that nozzles and spray orifices are
functioning correctly. The inspection
should be made with the circulation pump
on and fans off.

Mist Eliminators

The mist eliminators must be correctly
positioned when they are replaced during
cleaning or service.

Air Inlet

Inspect the air inlet louvers and mist
eliminators into the condenser section on a
monthly basis to remove any paper, leaves or
other debris that may block the airflow.

Stainless Steel Base Pan

The  base  pan  under  the  tube  bundles  is
stainless  steel  and  may  sometimes  become
tarnished  due  to  contamination.  These
surfaces should be inspected yearly to ensure
they remain clean of any contamination that
may  result  in  damage.  Any  surfaces  that
show  contamination  should  be  cleaned
ONLY  with  a  commercial  stainless  steel
cleaner to restore the initial appearance.

Propeller Fans and Motors

The fans are directly mounted on the motor
shafts and the assemblies require minimal
maintenance except to assurance they are
clear of dirt or debris that would impede the
airflow.

Recommended Annual Inspection

In  addition  to  the  above  maintenance
activities,  a  general  inspection  of  the  unit
surface  should  be  completed  at  least  once  a
year. Remove spray header and flush out.

Cleaning

Mechanical  cleaning,  including  pressure
washing,  should  never  be  performed  as
surfaces  and  seals  could  be  damaged.
Chemical  cleaning  that  is  safe  for  stainless
steel,  copper,  aluminum,  ABS  plastic  and
PVC is the only acceptable means of cleaning
the  evaporative  condenser.  A  proper  water
treatment  program  should  reduce  cleaning
needs.

«
...
66
67
68
69
70
...
»

Содержание LZ Series









































































































Отзывы:

Нет отзывов

Похожие инструкции для LZ Series

Бренд: Daikin Страницы: 16

Бренд: Vito Agro Страницы: 72

Бренд: AEG Страницы: 60

Бренд: Chill Solutions Страницы: 7

AFFINITY P Series

Бренд: Lydall Страницы: 29

Multiplex 42 MR04

Бренд: Manitowoc Страницы: 52

Бренд: MTD Страницы: 2

Бренд: MTD Страницы: 1

Бренд: MTD Страницы: 11

Бренд: MTD Страницы: 16

Бренд: MTD Страницы: 16

Бренд: MTD Страницы: 20

Бренд: MTD Страницы: 24

Бренд: Raider Страницы: 30

Бренд: Sandr Garden Страницы: 64

Бренд: Nakayama Страницы: 21

Бренд: Yard Machines Страницы: 24

Бренд: York Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды