AAON LZ Series страница 67 Скачать руководство пользователя | Manualshive

Страница: 67 / 104

background image

67

ambient  temperature  is  below  32°F,  the
condenser  pump  will  not  operate.  As  the
ambient temperature increases, the condenser
pump  will  activate  at  35°F.  As  the  ambient
temperature  decreases,  the  condenser  pump
will  deactivate  at  32°F.  This  dead  band
prevents  the  condenser  pump  from  cycling
too  much.  Below  32°F,  the  unit  operates  as
an  air-cooled  condenser.  An  optional  sump
heater

operates

when

the

ambient

temperature  is  below  40°F  to  prevent  the
sump  from  freezing  and  offers  freeze
protection to 0°F.

Pump Maintenance

Cleaning  -  Remove  oil,  dust,  water,  and
chemicals from exterior of motor and pump.
Keep  motor  air  inlet  and  outlet  open.  Blow
out  interior  of  open  motors  with  clean
compressed air at low pressure.

Labeled Motors

- It is imperative for repair of

a  motor  with  Underwriters’  Laboratories
label that original clearances be held; that all
plugs,  screws,  other  hardware  be  fastened
securely, and that parts replacements be exact
duplicates  or  approved  equals.  Violation  of
any  of  the  above  invalidates  Underwriters’
Label.

Fan Motor Maintenance

Same as pump maintenance.

Access Doors

If scale deposits or water is found around the
access  doors,  adjust  door  for  tightness.
Adjust as necessary until leaking stops when
door is closed.

The  evaporative  condenser  doors  have  an
adjustable fit design. A good seal and fit are
key  to  avoid  leaks.  A  leak  inspection  is
recommended  during  installation  and  every
six (6) months thereafter. If a leak is found,
use the following steps to adjust the fit of the

door. This process will require at least two (2)
people.

1.

Identify and locate the leak(s).

2.

Make sure the evaporative condenser
is not running while working on this
process.

3.

Open the door and check for damage
to the seal or the frame.as well as the
engagement of the door seal with the
frame.

4.

Replace the seal if damage is found.

5.

Check to see if this fixed the issue.

6.

If the issue persists, the next step is to
check the fit of the door.

7.

Disengage the closing mechanism of
the door that has a leak.

8.

One person must hold the door, while
the other slowly loosens the four (4)
bolts on the two (2) hinges connecting
the door to the hinge.

Figure 36 – Evaporative condenser access

door

9.

Adjust the door as needed to create a
good seal all around the door.

10.

Tighten the bolts to secure the door in
place.

11.

Run the evaporative condenser and
check to make sure the issue has been
solved.

12.

Repeat as needed.

LOOSEN
THESE BOLTS

«
...
65
66
67
68
69
...
»

Содержание LZ Series









































































































Отзывы:

Нет отзывов

Похожие инструкции для LZ Series

Бренд: BAC Страницы: 44

Бренд: CyberChill Страницы: 12

Бренд: Garland Страницы: 180

Бренд: Jensen Страницы: 110

Бренд: Timberwolf Страницы: 50

Craftsman 247-795890

Бренд: Sears Страницы: 24

Yard Machines 450 Series

Бренд: MTD Страницы: 36

Бренд: MTD Страницы: 28

Бренд: MTD Страницы: 11

Бренд: MTD Страницы: 20

Бренд: Johnson Controls Страницы: 34

YORK YCAL0043E Series

Бренд: Johnson Controls Страницы: 188

Бренд: VESEYS Страницы: 32

Blue Chilled 40 693

Бренд: Grohe Страницы: 90

SEACHILL TK 3000

Бренд: Tank Страницы: 64

Бренд: Draper Страницы: 24

Hyperchill ICE076

Бренд: Parker Hiross Страницы: 172

Бренд: Royal Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды