AAON LZ Series Скачать руководство пользователя | Manualshive

Страница: 50 / 104

background image

50

Fan Assembly Bushings

The fan assembly bushings should be
tightened to the specifications listed in the
following table.

Table 10 - Fan Assembly Bushing Torque

Specifications

Boiler System Startup

Before starting the boiler system for the first
time, verify the following items have been
checked:

1. Verify that electrical power is available

and  that  the  voltage  is  correct  and  the
capacity  is  equal  to  or  greater  than  the
unit’s  MOP  listed  on  the  nameplate.
Verify  that  the  gas  supply  is  connected,
has  been  properly  sized,  and  has  been
purged of air.

2. Immediately after turning on the gas

supply, check piping for any leaks.

3. Verify that the city make-up water supply

is available and properly connected.
Open automatic air vents as shown in the
Automatic Air Vent Valves section.

4. Before applying power, review the MCS

Controller  manual  provided  with  the
chiller.  Understand the  operation of the
controller  display  panel  as  well  as  the
MCS  Connect  PC  program.    Review

manuals provided with each boiler for
proper operation of boiler controls.

5. Verify that the rotation of all pumps is

correct.  The rotations have been checked
at the factory, so if any motors that are not
powered by a Variable Frequency Drive
are  operating  backwards  two  phases
should  be  switch  at  the  unit  power
connection.

6. Verify that any remote stop/start device

or BMS signal is connected to the chiller
controller and requesting the boiler
system to start.

7. A building load of at least 25% of the

boiler capacity should be present in order
to properly check operation.

8. Complete the general check list at the top

of the startup form to make a last check
that the boiler system is ready to operate.

Test the boiler system operation by changing
the  Boiler  Run/Stop  switch  to  “Run”.    The
boiler  building  pump  should  then  start  and
the boilers should stage  on and modulate to
maintain

the

leaving

water

target

temperature. If not enough load is present to
stage on each boiler, disable individual units
through the boiler controls.

Use  the  startup  form  to  record  the  full  load
boiler  water  in  temperature  and  water  out
temperature  as  well  as  the  amps  for  each
individual boiler.

When  all  boilers  have  been  observed  to
function correctly, enable all boilers through
boiler  controls.    Observe  the  system  until  it
reaches  a  steady  state  of  operation.    If
necessary  adjust  the  boiler  leaving  water
setpoint  to  match  desired  target.    For  units
with  BMS  communication,  verify  that  the

Bushing

Tightening Torque

(in-lbs.)

H X 1.125"

95

H X 1.375"

95

SH X 1.125"

108

SH X 1.375"

108

SD X 1.125"

108

SD X 1.375"

108

SD X 1.625"

108

SD X 1.875"

108

SK X 2.125"

180

«
...
48
49
50
51
52
...
»

Содержание LZ Series









































































































Отзывы:

Нет отзывов

Похожие инструкции для LZ Series

Бренд: Echo Страницы: 18

Бренд: Piper Products Страницы: 67

EWAD620-C17C-SL

Бренд: Daikin Страницы: 304

Бренд: Neuton Страницы: 8

Бренд: PowerTek Страницы: 7

Бренд: Vermeer Страницы: 100

Бренд: Jonsered Страницы: 28

Бренд: Texas Equipment Страницы: 18

Бренд: Texas Equipment Страницы: 26

Бренд: Texas Equipment Страницы: 28

Бренд: VALERA Страницы: 2

Бренд: Qualcast Страницы: 20

Cool cabi OCA-S300AC-A100

Бренд: OHM ELECTRIC Страницы: 40

INTIMIDATOR 15XP/1390

Бренд: Bandit Страницы: 181

Бренд: Lawn Solutions Страницы: 8

Бренд: Daikin Страницы: 56

Бренд: Fast Chiller Страницы: 15

Бренд: York Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды