AAON LZ Series Скачать руководство пользователя | Manualshive

Страница: 42 / 104

background image

42

start  a  system  because  the  refrigerant  will
migrate  to  the  cold  part  of  the  system
(condenser)  and  make  it  difficult  for
refrigerant to flow.

The  low  ambient  system  maintains  normal
head pressure during periods of low ambient
temperatures  by  controlling  condenser  air
flow by modulating fan speed.  By reducing
condenser  air  flow,  the  condenser  heat
rejection  capacity  is  reduced.    This  allows
unit operation down to 0

°

F.

During  higher  ambient  temperatures,  the
entire  condenser  is  required  to  condense
refrigerant.  During  these  higher  ambient
temperatures,  full  condenser  air  flow  is
required  to  maintain  system  capacity.    The
VFD  controlled  condenser  fan  low  ambient
head  pressure  control  will  modulate  the
condenser  air  flow  to  maintain  proper  head
pressure.    Along  with  electronic  expansion
valves,  VFD  controlled  condenser  fans
optimize system performance.

Electrical

The electrical power connections are made in
the electrical control compartment.

The  microprocessor  control  furnished  with
the unit is supplied with its own power supply
factory  wired  to  the  main  power  of  the
outdoor mechanical room.

Verify the unit nameplate voltage agrees with
the power supply. Connect power and control
field  wiring  as  shown  on  the  unit  specific
wiring diagram provided with the unit.

Size  supply  conductors  based  on  the  unit
MCA  rating.  Supply  conductors  must  be
rated a minimum of 167°F (75°C).

Route power and control wiring, separately,
through  the  utility  entry.  Do  not  run  power
and signal wires in the same conduit.  Power

and signal wires in the same conduit can
cause electrical interference.

Table 4 - Nameplate Voltage Markings

Voltage Feature

Nameplate

Voltage

Marking

Min/Max

VAC

2 230V/3Φ/60Hz

230

197/252

3 460V/3Φ/60Hz

460

456/504

4 575V/3Φ/60Hz

575

570/630

8 208V/3Φ/60Hz

208

197/228

Protect the branch circuit in accordance with
code requirements. The unit must be
electrically grounded in accordance with
local codes, or in the absence of local codes,
the

current

National

Electric

Code,

ANSI/NFPA  70  or  the  current  Canadian
Electrical Code CSA C22.1.

Power wiring is to the unit terminal block or
main disconnect. All wiring beyond this point
has  been  done  by  the  manufacturer  and
cannot  be  modified  without  affecting  the
unit's agency/safety certification.

Electric

shock

hazard.

Before

attempting to perform any installation,
service,  or  maintenance,  shut  off  all
electrical  power  to  the  unit  at  the
disconnect  switches.  Unit  may  have
multiple  power  supplies.  Failure  to
disconnect  power  could  result  in
dangerous  operation,  serious  injury,
death or property damage.

WARNING

«
...
40
41
42
43
44
...
»

Содержание LZ Series









































































































Отзывы:

Нет отзывов

Похожие инструкции для LZ Series

Бренд: ACS Страницы: 83

Бренд: Poulan Pro Страницы: 28

Бренд: Nakayama Страницы: 17

Бренд: Milestone Страницы: 72

Master-Chill MCR-33-101PT

Бренд: Master Bilt Страницы: 58

Бренд: intensity Страницы: 32

Бренд: Trane Страницы: 86

Бренд: Troy-Bilt Страницы: 28

Бренд: Honda Страницы: 64

Бренд: Honda Страницы: 60

Бренд: Honda Страницы: 60

Бренд: Honda Страницы: 270

Бренд: A.B.Energy Страницы: 29

Бренд: Clint Страницы: 28

Бренд: Powermate Страницы: 48

Бренд: Cool Compact Страницы: 22

Бренд: Cool Compact Страницы: 64

Бренд: Flymo Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды