Aanderaa DCPS 5400 Скачать руководство пользователя страница 122

Страница: 122 / 150

Page 122

July 2019 – TD 304 OPERATING MANUAL – Doppler Current Profiler Sensor

10 and

Binary: xxxx11xxxxxxxxxx

Hexadecimal: xCxx

Cell has High vertical current, above high vertical limit 3, default 30

cm/s

Binary: xxx1xxxxxxxxxxxx

Hexadecimal: 1xxx

Cell inside blanking zone

Binary: xx1xxxxxxxxxxxxx

Hexadecimal: 2xxx

Cell inside illegible zone

Binary: x1xxxxxxxxxxxxxx

Hexadecimal: 4xxx

Cell out of range

Binary: 1xxxxxxxxxxxxxxx

Hexadecimal: 8xxx

Data not ready

The cross correlation is normally close to 0.5, high limit is 0.6

Indicates high single ping standard deviation on horizontal speed.. Narrowband and Broadband have different limits.

The limit input is set as single ping standard deviation per meter since it is dependent on the cell size (and pulse length).

The limits for Broadband are 10, 30 and 50 cm/s. The limits for narrowband are 60, 80 and 100 cm/s. These limits are

used for a 1 meter cell (and pulse). The standard deviation limits used are calculated from these as follows, SP Stdev

limit = SP Stdev per meter limit/sqrt(cellsize*pulselength). Broadband uses a fixed pulse length = 1m. In narrowband the

pulse length follows the column with the smallest cell size. If for example narrowband with 2m cell size and 2m pulse

length, the single ping standard deviation limits becomes 30, 40 and 50 cm/s.

The cell can have been configured to be behind the instrument or very close to the instrument. This can also change

during the deployment dependent on water level changes and sensor tilt.

The illegible zone: if surfaced referred column, approximately 10% of the distance from surface to the instrument is

contaminated by side lobes.

Cells can have been configured to be too far away. Tilting of the instrument can also result in out of range on some of

the beam cells.

Table 5-7: Cell State2 (For SW version 8.3.6. and newer. For older version see previous version.)

Cell State2 bits

Meaning

Bit no

Bit pattern (x don’t care)

Binary: xxxxxxxxxxxxxxx1

Hexadecimal: xxx1

Beam1 cell inside blanking zone

Binary: xxxxxxxxxxxxxx1x

Hexadecimal: xxx2

Beam2 cell inside blanking zone

Binary: xxxxxxxxxxxxx1xx

Hexadecimal: xxx4

Beam3 cell inside blanking zone

Binary: xxxxxxxxxxxx1xxx

Hexadecimal: xxx8

Beam4 cell inside blanking zone

Binary: xxxxxxxxxxx1xxxx

Hexadecimal: xx1x

Beam1 cell out of range (too far away)

Содержание DCPS 5400























































































































































Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды

Aanderaa DCPS 5400, Руководство по эксплуатации

Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды