A&D AD-8923-BCD Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 28

A&D AD-8923-BCD Скачать руководство пользователя страница 4

4

1. INTRODUCTION

This manual describes how the AD-8923-BCD remote controller works and how to get the most out of it
in terms of performance.
Read this manual thoroughly before using the AD-8923-BCD and keep it at hand for future reference.

1.1. Features

Connecting the AD-8923-BCD remote controller to a weighing instrument will enable transmission of RS-
232C weight data from the weighing instrument to a PLC using BCD output.

Displays the weight data transmitted from the weighing instrument.
Can change the weighing speed of the AD-4212C/D/F, perform sensitivity adjustment with the AD-

4212C/D/F using an external weight and share the power supply with the AD-4212C/D/F.

Note

When connected to the following instruments, power can be supplied to both instruments

by plugging the AC adapter into either the weighing instrument or the AD-8923-BCD.

(Both instruments can have their AC adapter connected at the same time.)

Compatible models: AD-4212C/D/F, FZ, FX, GX-A, GF-A, GX-M, GF-M, GX-L, GF-L, HR-AZ,

HR-A (Refer to “

3.3. Turning the power on

«
...
2
3
4
5
6
...
»

Содержание AD-8923-BCD





























Отзывы:

Нет отзывов