AAF FabriPulse M Скачать руководство пользователя страница 26

Страница: 26 / 37

FabriPulse

2015 American Air Filter Company, Inc. Any use of the text or

images this document contains, without permission of American Air

Filter Company, Inc., is prohibited. FabriPulse, AAF, REDClean,

REDFiltration, and Reliable Efficient Durable are registered

trademarks of American Air Filter Company, Inc. d/b/a AAF

International.

Start the fan with the fan damper or duct blast gates partially open. At

the same time observe the differential pressure of the control. This gauge

indicates the differential pressure across the dust cake and fabric. Rising

pressure on the gauge shows that dust is being collected on the bag. When

the gauge shows 3” to 5” w.g., the fan damper or duct blast gates may be

opened to the full normal position. Simultaneously, the power should be

turned on to the control panel.

Check the differential pressure gauge again. It should read a minimum

of 3” to 4” w.g. with slight fluctuations each time a pulse occurs. If the

differential pressure is not 3” to 4” w.g., the factory preset pulse interval

must be changed. Decrease the “high” differential pressure for high pressure

readings and increase the “high” differential pressure for low pressure

readings. Should it not be possible to maintain the nominal 3” to 4” w.g.,

consult your AAF representative. DO NOT ADJUST THE PULSE DURATION

BEFORE CONSULTING AN AAF REPRESENTATIVE.

The procedure should also be followed after installing new bags in the

unit.

11.2

Normal operation

An understanding of the design and operating principle of the FabriPulse M is

essential for effective operation and maintenance. Knowledge of the collector

nomenclature is necessary so that parts can be easily identified and located.

The

FabriPulse

is a single compartment, continuous automatic, self-cleaning

cloth pulse-jet dust collector. The dirty air enters the collector through a high inlet

located on the side of the housing. As the dirty air passes through the filter media,

the dust is deposited on the outside surface of the individual filter bags. The

cleaned air leaves the filter media and rises through the inside of the bags to the

clean air plenum and is exhausted through the outlet.

The filter bags are periodically cleaned by bursts of compressed air that are

injected down the inside of the bags. Since only a few of the bags are cleaned at

one time the unit remains in continuous operation. The collected dust falls into the

hopper after each pulse.

Hoppers are designed to receive the dust and are not for storage. The

recommended practice is to continuously empty the hopper. When flat bottom

hoppers or barrels are used, they must be emptied on a periodic basis to prevent

Содержание FabriPulse M






































Результаты поиска

Содержание FabriPulse M

Отзывы:

Похожие инструкции для FabriPulse M

Бренды по названию

Популярные бренды

AAF FabriPulse M, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание FabriPulse M

Отзывы:

Похожие инструкции для FabriPulse M

Бренды по названию

Популярные бренды