A.R.C. Laser FOX 514 Скачать руководство пользователя страница 52

Страница: 52 / 56

User Manual FOX 514

September 2021

File: User Manual_FOX 514_rev3

10.4 Recommended separation distances between portable and mobile RF

telecommunications equipment and the laser

The laser is intended for use in an electromagnetic environment in which the RF disturbances are controlled. The customer or the

user of the laser can help to avoid electromagnetic interference by maintaining the minimum distance between portable and

mobile HF telecommunication devices (transmitters) and the laser - depending on the output power of the communication device,

as stated below.

Test

frequency

MHz

Frequency

band

MHz

Radio

service

Modulation

Maximum

performance

Distance

Immunity test level

V/m

385

380 to 390

TETRA 400

Pulse

modulation

18Hz

1.8

0.3

450

430 to 470

GMRS 460

FRS 460

± 5 kHz Hub

1 kHz Sinus

0.3

710
745
780

704 to 787

LTE Band

13,17

Pulse

modulation

217 Hz

0.2

0.3

810
870
930

800 to 960

GSM

800/900,

TETRA 800,

iDEN 820,

CDMA 850,

LTE Band 5

Pulse

modulation

18 Hz

0.3

1720
1845
1970

1700 to

1990

GSM 1800,

CDMA 1900,

GSM 1900,

DECT,

LTE Band

1,3,4,25,

UMTS

Pulse

modulation

217 Hz

0.3

2450

2400 to

2570

Bluetooth,

WLAN

802.11 b/g/n,

RFID 2450,

LTE Band 7

Pulse

modulation

217 Hz

0.3

5240
5500
5785

5100 to

5800

WLAN

801.11 a/n

Pulse

modulation

217 Hz

0.2

0.3

Содержание FOX 514

























































Результаты поиска

Содержание FOX 514

Отзывы:

Похожие инструкции для FOX 514

Бренды по названию

Популярные бренды

A.R.C. Laser FOX 514, Руководство пользователя

Результаты поиска

Содержание FOX 514

Отзывы:

Похожие инструкции для FOX 514

Бренды по названию

Популярные бренды