A.O. Smith GCV Series страница 11 Скачать руководство пользователя | Manualshive

Страница: 11 / 44

background image

11

Energy Cut Off (ECO):

A metal tube (Temperature

Probe) mounted onto the back of the gas control
valve/thermostat is immersed inside the tank water.
The probe acts as a temperature high limit. If water
gets excessively hot, an Energy Cut Off (ECO) switch
within the probe opens, interrupting the small electrical
current to the gas valve, and gas

fl

ow through the

control is interrupted. NOTE: If this safety sensor opens,
the entire control must be replaced. The ECO is NOT
resettable.

Thermal Cut Off Switch (TCO):

The water heater

is also equipped with a resettable thermal switch,
designed to shut off the gas supply in the event the
water heater has been exposed to high combustion
chamber temperatures caused by

fl

ammable vapors

(e.g. spilled gasoline), poor combustion caused by a
blocked vent or insuf

fi

cient combustion air.

Gas:

When you prepare to light the pilot, you are

instructed to turn the gas control knob to the pilot
position and depress the gas control knob (Reset button
on Robertshaw Gas Valves). When depressed gas will

fl

ow to the pilot burner only. You then have to (manually)

ignite this pilot gas using the piezo igniter button. When the pilot is lit, the

fl

ame must heat the thermocouple until

it generates suf

fi

cient voltage to the gas valve to allow you to release the knob while gas continues to

fl

ow to

the pilot. When the gas control knob is turned to the “ON” position, gas is also available to the main burner if the
thermostat calls for heat.

Water Flow:

When a hot water faucet is opened, water pressure from the well tank or street main forces cold

water into the water heater through the dip tube. This pushes hot water out of the tank.

BASIC INSTALLATION & OPERATION

Figure 5

Reset Button

TCO Reset

Button

NOTE: RobertShaw® Gas Control
Valve/Thermostat shown.

Gas Control Valve/Thermostat - Side View

Gas Control Knob

Gas Inlet

Temperature

Probe

Protective

Plastic Sleeve

Thermocouple

Temperature

Sensor

ECO

TCO (Thermal

Cut Off) Sensor

TCO (Thermal

Cut Off) Switch

«
...
9
10
11
12
13
...
»

Содержание GCV Series













































Отзывы:

Нет отзывов

Похожие инструкции для GCV Series

Бренд: Fenix Страницы: 8

Бренд: Q-Pumps Страницы: 22

Бренд: Nakayama Страницы: 8

DynaFLO DOWB-S1 Series

Бренд: Camus Hydronics Страницы: 28

Бренд: Dancover Страницы: 7

Бренд: MasterCraft Страницы: 8

Бренд: Ulvac Страницы: 27

Бренд: Endress Страницы: 17

New XR Designer

Бренд: Haverland Страницы: 8

RADSON MIED0508EL

Бренд: Purmo Страницы: 32

Бренд: Campbell Страницы: 2

Бренд: L.B. White Страницы: 16

PROFESSIONAL OHIR18LV

Бренд: Dyna-Glo Страницы: 6

Бренд: nedis Страницы: 7

GPVX 75L Series

Бренд: A.O. Smith Страницы: 52

Бренд: Parmet Страницы: 6

Бренд: FE PETRO Страницы: 16

HOTSPRING HSTB9

Бренд: ZANSKAR Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды