background image

2

safE InstallatIon, usE and sErVICE

Your safety and the safety of others is extremely important in the installation, use, and servicing of this water heater.

Many safety-related messages and instructions have been provided in this manual and on your own water heater to warn you and 

others of a potential injury hazard.  Read and obey all safety messages and instructions throughout this manual.  It is very important 

that the meaning of each safety message is understood by you and others who install, use, or service this water heater.

This is the safety alert symbol. It is used to alert 

you to potential personal injury hazards. Obey all 

safety messages that follow this symbol to avoid 

possible injury or death.

 

danGEr

danGEr indicates an imminently hazardous 

situation which, if not avoided, will result in 

death or injury.

 

warnInG

warnInG indicates a potentially hazardous 

situation which, if not avoided, could result 

in death or injury.

 

CautIon

CautIon indicates a potentially hazardous 

situation which, if not avoided, could result 

in minor or moderate injury.

CautIon

CautIon used without the safety alert 

symbol indicates a potentially hazardous 

situation which, if not avoided, could result 

in property damage.

all  safety  messages  will  generally  tell  you  about  the  type  of  hazard,  what  can  happen  if  you  do  not  follow  the  safety 

message, and how to avoid the risk of injury.

the  California  safe  drinking  water  and  toxic  Enforcement act  requires  the  Governor  of  California  to  publish  a  list  of 

substances  known  to  the  state  of  California  to  cause  cancer,  birth  defects,  or  other  reproductive  harm,  and  requires 

businesses to warn of potential exposure to such substances.

this product contains a chemical known to the state of California to cause cancer, birth defects, or other reproductive 

harm. this appliance can cause low level exposure to some of the substances listed.

IMportant dEfInItIons

•  

  Qualified Installer or Service Agency:

 

Installation and service of this water heater requires ability equivalent to that of a Qualified Agency (as defined by ANSI below) in 

the field involved. Installation skills such as plumbing and electrical supply are required in addition to electrical testing skills when 

performing service.

•  

  ANSI Z223.1 2006 Sec. 3.3.83:

 

 

“Qualified Agency” - “Any individual, firm, corporation or company that either in person or through a representative is engaged in and is 

responsible for (a) the installation, testing or replacement of gas piping or (b) the connection, installation, testing, repair or servicing of 

appliances and equipment; that is experienced in such work; that is familiar with all precautions required; and that has complied with all 

the requirements of the authority having jurisdiction.”

Содержание DHE200 THRU 10























Отзывы: