A-Maize-Ing Heat NRP620-10 Скачать руководство пользователя страница 81

Страница: 81 / 87

NRP620-9 OMEPAPV20161017 (ENGLISH) REV 1

Page 36 of 42

CANADIAN REQUIREMENTS FOR

SUPPLEMENTARY (ADD-ON) FURNACES

DO NOT USE DUCT ELBOWS HAVING AN INSIDE RADIUS OF LESS THAN 6 in. (150 mm) ON

THE OIL, ELECTRIC, OR GAS FURNACE.

DO NOT CONNECT IN SERIES TO A DOWNFLOW FURNACE.

DO NOT CONNECT DUCTWORK SO THAT A REVERSE FLOW IS POSSIBLE.

OPERATE THE GAS, OIL, OR ELECTRIC FURNACE PERIODICALLY TO ENSURE THAT IT WILL

OPERATE SATISFACTORILY WHEN NEEDED.

CERTIFIED FOR INSTALLATION WITH THE FOLLOWING DUCTWORK CONFIGURATIONS ONLY.

DO NOT RELOCATE OR BYPASS ANY OF THE SAFETY CONTROLS IN THE ORIGINAL GAS, OIL,

OR ELECTRIC FURNACE INSTALLATION.

DO NOT CONNECT TO ANY GAS FURNACE THAT HAS NOT BEEN CERTIFIED INITIALLY AS

COMPLYING WITH CAN/CGA-2.3

THE OPERATION OF THE GAS FURNACE MUST BE VERIFIED FOR ACCEPTABLE OPERATION

BEFORE AND AFTER INSTALLATION OF THE ADD-ON APPLIANCE BY A GAS FITTER WHO IS

RECOGNIZED BY THE REGULATORY AUTHORITY.

DO NOT CONNECT TO ANY GAS FURNACE THAT IS NOT EQUIPPED WITH AN AIR-

CIRCULATION BLOWER, OR TO A CHIMNEY OR VENT SERVING A GAS FURNACE OR GAS

APPLIANCE.

10.

THE ADD-ON UNIT SHOULD ONLY BE INSTALLED ON A FURNACE DUCT SYSTEM AND

CHIMNEY THAT ARE IN GOOD OPERATING CONDITION.

11.

THE MOTORS ON THE UNIT SHOULD NOT BE CHANGED, HOWEVER, THE SPEED OF THE

CONVECTION AIR MOTOR MAY BE INCREASED BY SELECTING THE APPROPRIATE MOTOR

SPEED LEAD. THE BLOWER CAN NOT BE CHANGED. THIS EQUIPMENT SHOULD BE

INSTALLED, ACCEPTABLE TO REGULATORY AUTHORITY, BY EXPERIENCED LICENSED

PERSONNEL.

12.

THE INSTALLATION SHOULD COMPLY WITH REQUIREMENTS OF CAN/CSA-B365, AND

CHANGES TO THE INSTALLATION SHOULD COMPLY WITH CSA B139 (FOR OIL-FIRED), C22.1

(FOR ELECTRIC), OR CAN/CGA-B149.1 OR CAN/CGA-B149.2 (FOR GAS-FIRED).

13.

MAY BE USED WITH GAS, OIL, AND ELECTRIC FURNACES UP TO 120,000 BTU.

Содержание NRP620-10
























































































Результаты поиска

Содержание NRP620-10

Отзывы:

Похожие инструкции для NRP620-10

Бренды по названию

Популярные бренды

A-Maize-Ing Heat NRP620-10, Руководство пользователя

Результаты поиска

Содержание NRP620-10

Отзывы:

Похожие инструкции для NRP620-10

Бренды по названию

Популярные бренды