background image

Sync and Async Modes 

The 

Mini PEG 

can operate in 

Sync 

or 

Async 

mode. Most of the 

time, the difference between the two modes is not important 

and the mode will automatically change in an intuitive way. 

In 

Sync 

mode, the envelope will always begin and end on the 

divided/multiplied ping clock, but in 

Async 

mode the envelope 

can begin at any point in time. Thus, 

Sync 

mode locks the 

phase of the envelope and the divided/multiplied ping clock 

together, while 

Async

 mode allows for any phase difference. 

Changing Between Sync and Async Mode 

• To enter 

Sync

 mode, fire a trigger into the 

Trigger 

jack while 

it’s configured as a Quantized Trigger jack. Or, you can fire a 

trigger into the 

Cycle 

jack while it’s configured to enter Sync 

mode. See System Mode for instructions on how to configure 

the jacks. 

• To enter 

Async 

mode, fire a trigger into the 

Trigger 

jack when it’s configured as an Async Trigger or 

Async Gate jack. 

• You can toggle modes by holding down 

Cycle

, tapping 

Ping

, then releasing 

Cycle

In 

Sync 

mode, the 

Ping 

button flashes cyan. In 

Async

 mode, the 

Ping 

button flashes white. 

Figure 1 illustrates envelopes in each mode. The 

Mini PEG 

begins cycling in 

Sync 

mode: each 

envelope starts o 

n a ping clock pulse. When a trigger is fired into the 

Trigger 

jack (which is set to 

Async Trigger or Gate mode), the envelope immediately resets and continues cycling out-of-phase with 

the ping clock. The module has now changed to 

Async

 mode automatically. In this case, it’s not 

important that you know what mode the module is in, it’s just doing 

what you told it to do. 

Cycle Button in Sync and Async Mode 

When using the 

Cycle

 button, it can be important to know whether  

the 

Mini PEG 

is in 

Sync 

or 

Async 

mode. 

When you turn on the 

Cycle 

button in 

Sync 

mode, the envelope will 

immediately start outputting from the same phase as the ping clock. 

You can imagine this as if the envelope was always running (in 

sync with the ping clock), and the 

Cycle 

button un-mutes it. See 

Figure 2. This can cause some discontinuities, but the envelope will 

always be in sync with the ping clock. When you turn 

Cycle 

off, 

the output will stop after the current envelope finishes. 

If you turn on the 

Cycle 

button in 

Async 

mode, the envelope will 

immediately start outputting from zero. One or more complete 

envelopes will always be output, but they will be synced to your 

button press, not to the ping clock. See Figure 3.  

Modulating Div/Mult in Sync and Async Mode 

If you change the 

Div/Mult

 amount while an envelope is running, 

the module’s response will depend on whether it’s in 

Sync

 or 

Async

 Mode. In both modes, the envelope slope will track the 

Div/Mult

 amount as long as the amount keeps changing. 

In 

Sync 

mode, if no change to the 

Div/Mult

 is made for 50ms, 

then the envelope will re-sync to the ping clock based on the 

new 

Div/Mult

 amount. See Figure 4. The 

Div/Mult 

knob was 

turned from /2 to = at the black arrow. Between the black and 

red arrows, the envelope makes a quick transition to a new 

envelope which is in sync with the ping clock. Notice how every 

envelope starts and ends exactly on a ping clock, even though 

we changed envelope lengths. 

In 

Async

 mode there is no requirement that the envelopes sync 

to the ping clock, so it will transition smoothly between 

waveforms without any re-syncing. See Figure 5. The envelope 

tracks the changes in the 

Div/Mult 

amount but never needs to 

Page   of 

7

12

Figure 1: Envelope (green) is synced to 
Ping clock (magenta) until an Async 
Trigger (gold) is received

Figure 2: Pressing Cycle button in 
Sync mode.

Figure 3: Pressing Cycle button in 
Async mode.

Figure 4: Changing Div/Mult in Sync Mode

Содержание Mini PEG













Отзывы: