background image

Hover Racer

WARNING:
CHOCKING HAZARD - Small parts.
Not for Children under 3 years.
To Parents: Please read all instructions before giving guidance to your children.

A. SAFETY MESSAGES
1. This kit is intended for children aged 10 and over. All project-related assembly and operations should be
done under adult supervision.
2. This kit and the finished product contain small parts which may constitute a choking hazard if used
inappropriately. Keep away from children under 3 years of age.
3. To prevent potential short-circuits, never touch the contacts inside the battery compartment with any
metal object.
4. Carefully examine the plastic propeller before you put in on the motor spindle. If you see any defects in the
blades or on the outer rim, do not run the motor. Refer to the Questions and Comments section on this sheet
and contact our customer service for a replacement.
5. The propeller spins at high speed when the motor is turned on. To prevent potential injuries, do not touch
it with your fingers or any objects. Adult supervision is required throughout.
6. Verify that the switch is turned off when inserting/replacing the batteries. Otherwise the propeller will
spin immediately once all batteries are installed

B. USE OF BATTERIES
1. This kit requires four AAA, 1.5-volt batteries (not included).
2. For best results, always use fresh batteries.
3. Insert the batteries in the battery compartment according to the correct polarities.
4. Remove the batteries when not in use.
5. To prevent potential damage to the kit, immediately replace drained batteries.
6. Rechargeable batteries must be removed from the kit before recharging.
7. Rechargeable batteries must be recharged under adult supervision.
8. Do not attempt to charge non-rechargeable batteries.
9. Do not mix old and new batteries.
10. Do not mix alkaline, standard (Carbon-Zinc) or rechargeable (Nickel-Cadmium) batteries.
11. Ensure that the supply terminals are not short-circuited.

Содержание Hover Racer








Отзывы: