3onedata IES716-2GS Скачать руководство пользователя страница 44

Страница: 44 / 54

User manual

Page 44

In255Octets

Number of frames between128 and 255 bytes

(including invalid frames)

In511Octets

Number of frames between 256 and 511 bytes

(including invalid frames)

In1023Octets

Number of frames between 512 and 1023 bytes

(including invalid frames)

InMaxOctets

Number of 1024-1518 or 1522 bytes

（

802.1Q

）

(including invalid frames)

Jabber

Invalid oversized frames received (more than 1518

or 1522)

Oversize

Valid oversized frames received (more than 1518

or 1522)

InDiscards

Number of Valid discarded frames (because of

cache, flow control, etc.)

InFiltered

Valid frames filtered (because of VLAN and so on)

6.9.2 TX frame statistics

OutUnicasts

unicast data frames output

OutBroadcasts

Broadcast data frames output

OutPause

Number of output flow control pause frames

OutMulticasts

Multicast data frames output

OutFCSErr

Invalid FCS frames output

OutOctets

Number of output bytes

（

including FCS

）

Out64Octets

Number of output frames with 64 bytes

Out127Octets

Number of output frames between 65 and 127

bytes

Out255Octets

Number of output frames between 128 and 255

bytes

Out511Octets

Number of output frames between 256 and 511

bytes

Out1023Octets

Number of output frames between 512 and 1023

bytes

OutMaxOctets

Number of output frames between 1024 and 1518

or 1522 bytes

（

802.1Q

）

Collisions

Number of collision in output

Late

Number of collision after frames output 64 bytes

Excessive

Number of unsuccessful output frames

（

trying

more than 16 times with half duplex flow control

）

Multiple

Number of successful output frames

（

collision

more than 1 time

）

Single

Number of successful output frames

（

collision

happens in 1 time only

）

Deferred

Number of successful output frames

（

the receiver

is busy, but

It sends successfully after a delay

）

OutFiltered

Filtered frames output

OutDiscards

Discarded frames output

（

because of cache, flow

control, etc.

）

6.10 Diagnosis

6.10.1 Mirror

Содержание IES716-2GS























































Результаты поиска

Содержание IES716-2GS

Отзывы:

3onedata IES716-2GS, Руководство пользователя, Страница: 44 / 54

Результаты поиска

Содержание IES716-2GS

Отзывы: