3onedata IES716-2GS Скачать руководство пользователя страница 29

Страница: 29 / 54

User manual

Page 29

increase the bandwidth between the switch and network device, such as servers, routers, workstations,

or other switches. Trunking function is to integrate more than one physical port (typically 2-4) to a

logical channel.

（

Figure 6.6.1

）

Device supported 4 trunking group, operate method: choice apply, choice the port need to

trunking the port list, Choice setting, available after reboot. If the port already set to Ring port, it can

not set to trunking port. Each trunking group at least have 2 port member, at more 4. 1 port can not

exit in 2 trunking group.

1.The trunking groups require all the attributes can be the same, including speed, duplex, STP state etc.

2.If you do not confirm the STP state, please disable RSTP function, or close others, leaving only one STP
channel.

3.Port 1 as the system reserved, can not be used as trunking.

4.The ports of having been set to the port aggregation that can not be set to ring ports.

6.6.2 Rapid Ring

SW-Ring

technology provides auto-recovery and reconnection mechanism for broken network. When

network is broken, it has link redundancy and self-recovery capability and self-recovery time is less than

20ms. SW-Ring is the patented technology of

3onedata Co., Ltd. designed for industrial control network requiring high reliability.

SW-Ring

technology support maximum 250 pieces switches, in which the

SW-Ring

its self-

recovery time is <20ms.

Each port of IES7110 series switch can be Ring Port to connect other switches. When network is

broken, relay for failure alarm will be activated. Redundant organization of

SW-Ring

enable backup

link to recover network instantly.

Self-developed patented technology for SW-Ring network can realize the intelligent redundancy for

industrial Ethernet switch, which can make you easily and conveniently establish redundant Ethernet,

and can facilitate the quick recovery of any network section of automatic system disconnected from the

network. IES7110 series supports maximum 4 ring groups. Each group set up 2 ports as Ring Port and

a port cannot belong to several rings.

Hello_time setting is time interval of sending detecting packet to network at regular time. The unit is

Содержание IES716-2GS























































Результаты поиска

Содержание IES716-2GS

Отзывы:

3onedata IES716-2GS, Руководство пользователя, Страница: 29 / 54

Результаты поиска

Содержание IES716-2GS

Отзывы: