3onedata IES716-2GS Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 54

3onedata IES716-2GS Скачать руководство пользователя страница 14

User manual

Page 14

CHAPTER 6 WEB MANAGEMENT

IES716-2GS series have WEB server inside, can manage and maintenance the device

very intuitive

through WEB interface

6.1 Configurate preparing

1. The lowest requirement for user's computer is as below:



Install operating system (Windows XP/2000,etc)



Install Ethernet card



Install Web explorer (IE6.0 or higher version)



Install and start TCP/IP protocol

2. Establish the correct network configuration

The default management IP address of IES716-2GS: 192.168.1.254, subnet mask as: 255.255.255.0.

Before access to the configuration interface, the computer's IP address and the switch must be

configured in the same subnet (IP address configuration, please refer to "5.1") if need local

configuration; Computers and switches must be routed reach if for remote configuration.

How to log on to Web Server

Please type in the default IP of switch on the browsers’s address bar, and then will pop-up a

window by clicking the “enter” key which shows you have to enter your user name and password. The

default username and password is “admin”. You can enter your username and password 3 times if you

found the username and password is incorrect. If the 3 input error, the browser will display a "401

Unauthorized" error message. Refresh the page and then enter the correct user name and password,

log on to the Web Server, it will recommend to modify the user name and password. Please contact our

customer service center if you have more questions.

(Figure 6.1.1)

The default username and password is [admin], case sensitive for this series. The default password is

with administrator privileges.

«
...
12
13
14
15
16
...
»

Содержание IES716-2GS























































Отзывы:

Нет отзывов