3M SST Скачать руководство пользователя страница 48

Страница: 48 / 90

38 • Ch. 4 Preventive Maintenance

75-0302-1450-8, Version 1

SST Transport and Burster Mechanism Manual

Cleaning the SST Transport

The first step in preventive maintenance involves cleaning the SST Transport. This removes all of

the dust and other particles that may impact the SST Transport.

One of the components of the SST Transport that requires cleaning at regular intervals is the Ticket

Channel. Since sensor openings are recessed slightly in the Ticket Channel, they form pockets

which collect debris, mainly paper dust. As the pockets fill with paper dust, the dust begins to

block the transmission of light from the LED source to the sensor in the upper Ticket Channel.

When blocked completely, the SST Transport can no longer “see” a ticket and the system fails.

Since December 1998 the product has had a 3/8 in. (9.5 mm) wide strip of transparent film tape to

cover the sensor holes on the lower Ticket Channel. The strip is laid lengthwise and covers all of

Stop Latch

Figure 4.3

Opening the SST Transport

Stop Latch

Previous SST Transport

Stop Latch

SST/HP-1 Transport

SST/HP-4 Transport

Содержание SST



























































































Результаты поиска

Содержание SST

Отзывы:

Похожие инструкции для SST

Бренды по названию

Популярные бренды

3M SST, Руководство пользователя

Результаты поиска

Содержание SST

Отзывы:

Похожие инструкции для SST

Бренды по названию

Популярные бренды