3M
™
Speedglas
™
Welding Helmet 9100MP/9100MP-Lite
To optimise the effective lifetime of your welding equipment and avoid the additional cost of replacement, regular
maintenance is important. Replace all damaged parts immediately to ensure correct levels of protection.
•
Helmet and head harness.
Inspect for cracks or any
damaged or defective parts. Replace if needed.
•
Cover lenses.
To provide the best possible
vision they should be clean and without scratches.
•
Face seal.
If the face seal is damaged there is a great
risk that contaminated air will get inside the helmet.
Verify it’s in position and free from splits and tears.
•
Welding lens.
Ensure low battery is not flashing
and check that the sensors are clean and uncovered.
•
Breathing tube.
Confirm tube is not damaged or
leaking any air. To extend the life of breathing tube,
use a tube cover or a heavy-duty rubber tube.
Before use
After use
•
Clean the helmet.
Wipe with a moist tissue or cloth,
both inside and outside the helmet. If you suspect that the inside
of the airduct is dirty, it must be changed.
DO NOT rinse, immerse in water or clean with solvents.
•
Face seal and sweatband.
Remove for additional cleaning as
needed and replace if they become unhygienic.
•
Cover lenses.
Clean with a soft cloth and replace if any pits or
scratches occur.
•
Breathing tube.
Replace if damaged, deformed or leaking any air.
•
Storage.
Store the helmet in a dry, clean area away from direct
sunlight, high temperatures and solvents.
Care & Maintenance
To request a quote or place an order for spare parts, please contact TWS on +61 (0)
7
46
5
9 0044 or visit www.tweld.com.au. Please note that higher than normal levels
of pollutants, heat and sparks will require more frequent replacement of components. If you require additional guidance, please check the care and maintenance videos on our
YouTube Channel (
www.youtube.com/user/3MSpeedglas
) or contact your local TWS representative.
Further information and advice
Authorised 3M Wholesaler
Unit 13, 39 Herbert Street • St Leonards NSW 2065 • Australia
T: (02) 9439 0111 • F: (02) 9439 0100
W: www.speedglas.com.au
171022
171023
171024
197011
197150
197151
422000
500026
523000
523001
526000
527000
527070
528025
531000
532016
533001
533505
534200
536200
540500
570495
570895
572800
592800
790101
896055
896056
SWEATBAND 100 & 9100 MP PK=2
SWEATBAND 100 & 9100 MP PK=5
SWEATBAND 100 & 9100 MP PK=50
SAFETY HELMET COVER 9100 MP/MP-LITE
SHROUD 9100 MP/MP-LITE
LENS MAGNIFYING 1.0X 9100 100 & 9000
LENS MAGNIFYING 1.5X 9100 100 & 9000
LENS MAGNIFYING 2.0X 9100 100 & 9000
LENS MAGNIFYING 2.5X 9100 100 & 9000
LENS MAGNIFYING 3.0X 9100 100 & 9000
EARMUFFS WITH HELMET ATTACHMENT 9100 MP
FLIP UP MECHANISM 9100 MP
PIVOT KIT 9100 MP
BATTERY LITHIUM 9100, 100 & 9000 PK=2
LENS WELDING 9100XXi SPEEDGLAS
VISOR PLATE 9100 FX PK=5
VISOR PLATE ANTI-FOG 9100 FX PK=5
LENS COVER OUTER STD 9100 PK=10
COVER LENS OUTER HC 9100 PK=10
LENS COVER OUTER HT 9100 PK=10
LENS COVER INNER 9100XX PK=5
HOLDER BATTERY 9100
SIDEWINDOWS COVER PLATE 9100 FX PK=2
HEAD HARNESS 9100 MP
ADAPTOR ADFLO BREATHING TUBE 9100 MP AIR
FACE SEAL 9100 MP
HEAD HARNESS BACK PART 9100
FRONT COVER KIT 9100 FX
Part No
168502
168505
168550
169014
169015
171020
171021
Description
Part No Description
Part No Description
Part No Description
SHELL OUTER 9100 MP
SHELL INNER 9100 MP
HELMET WELDING WITH HARD HAT 9100 MP
WELDING HELMET BUMP CAP 9100 MP-LITE
CARRY BAG SPEEDGLAS
HARD HAT 9100 MP
BUMP CAP 9100 MP-LITE
53 42 00
19 71 51
89 60 55
89 60 56
19 71 50
57 08 95
54 05 00
52 30 00
52 30 01
57 04 95
16 85 02
16 85 05
16 85 50
53 62 00
53 20 16
17 10 20
17 10 21
17 10 22
17 10 23
17 10 24
50 00 26
53 10 00
42 20 00
52 80 25
53 35 05
16 90 15
52 60 00
52 70 00
52 70 70
16 90 14
197011
57 28 00 / 59 28 00
79 01 01
53 30 01
