3M QT-III Скачать руководство пользователя страница 1

Страница: 1 / 14

Cold Shrink Silicone Rubber

Termination QT-III

7672-S-8-TS

Instructions

IEEE Std. No. 48-1996

Class 1 Termination

69 kV Class 350 kV BIL

IEC 60840

72,5 kV

Kit Contents:

1 Silicone Rubber Lug Seal Insulator Assembly

1 Hi-K Stress Control Assembly

1 Silicone Rubber Insulator Assembly

1 Silicone Rubber Skirted Insulator Assembly

1 Pre-formed Ground Braid Assembly

3 Constant Force Springs

1 Roll Scotch

Electrical Shielding Tape 24

6 Tubes P55/R Red Compound (Non-Silicone Grease)

1 Roll Scotch

Sealing Mastic 2229, 1" (25 mm) wide

8 Strips Hi-K Mastic (1-6"

22", 7-2"

11")

1 Roll Scotch

Silicone Rubber Tape 70

1 Roll Scotch

Vinyl Electrical Tape Super 88, 1½"

44'

1 6" (150 mm) Hi-K Mastic Pad

1 3M

™

Cable Cleaning Pads CC-3

1 Copper Foil Tape Strip 1181, 15" long

4 Instruction Sheets

Note: Do not use knives to open plastic bags.

Kit Number

Primary Insulation

O.D. Range

Jacket O.D. Range

Conductor Size Range

AWG (mm

)

7672-S-8

1.94"–3.08"

(49.3–75.4 mm)

2.45"–3.35"

(62.2–85.1 mm)

250–1750

(120–850)

Table 1

4APE3HIELDED#ABLE

™

Cold Shrink Silicone Rubber

Skirted Termination Kit QT-III

for Tape Shielded Cable

7672-S-8-TS

78-8126-9537-3-B

CAUTION

Working around energized systems may cause serious injury or

death. Installation should be performed by personnel familiar with

good safety practice in handling electrical equipment. De-energize

and ground all electrical systems before installing product.

Содержание QT-III















Результаты поиска

Содержание QT-III

Отзывы:

Бренды по названию

Популярные бренды

3M QT-III, Быстрый старт

Результаты поиска

Содержание QT-III

Отзывы:

Бренды по названию

Популярные бренды