14
1. Use an approved work positioning device or stop at a designated resting platform.
2. Remain in positive contact with the ladder at all times, with both hands and feet.
3. Push the Sleeve above the chest position so that the cam is actively engaged with the wire before attaching a work
positioning device.
INSPECTION:
To ensure safe, efficient operation, the Cabloc/Cabloc Pro System should be inspected per the instructions
in Table 1 at the indicated frequencies.
;
Record the inspection results in “Periodic Examination and Repair History.”
DEFECTS:
If inspection or operation reveals a defective/damaged condition, remove and replace the defective/damaged
component(s).
6.0 MAINTENANCE & SERVICE:
Guidelines for maintenance and service are as follows:
•
The Cabloc/Cabloc Pro System is easily soiled by oil, grease, paint or other substances. Cleans it with a soft brush,
warm water and a mild detergent. Ensure the parts are thoroughly rinsed with plenty of clean water. Although highly
resistant to chemicals and environmental conditions, take all precautions to avoid contaminating the system with
acids, bitumen, cement, chloride, paint or aggressive cleaning fluids.
•
Stainless Steel parts are particularly susceptible to pitting corrosion from chlorine, so avoid exposure in this type
of environment. If the system is likely to be contaminated, please contact your 3M Certified Installer or 3M Fall
Protection for advice.
•
In areas where ice formation is possible, the System should be cleared of ice. When not in use, the Sleeve should be
stored per the following Storage recommendations.
STORAGE:
Store the Cabloc Sleeve and Cabloc Pro in a clean, dry, warm environment. Avoid areas where chemical
vapors may exist. Thoroughly inspect the Sleeve after extended storage. Clean and store body support and associated
system components according to the manufacturer’s instructions.
7.0 SPECIFICATIONS
7.1
All top and bottom anchors, cable guides, carrier cable, and fasteners are made of galvanized or stainless steel. Contact
3M Fall Protection for material specification details if required. The Cabloc/Cabloc Pro system, when installed according to
the installation instructions, meets CE (EN353-1:2014+A1:2017) requirements.
8.0 CABLOC SYSTEM LABELING
;
Please reference the User Manual supplied with the Cabloc/Cabloc Pro Detachable Sleeve for proper use and maintenance of this
system.
Cabloc/Cabloc Pro System:
The Cabloc/Cabloc Pro Vertical Cable Safety System tag must be securely attached and fully legible. Tag contents:
Figure 18:
1. Installation date.
7.
Next service date.
2. Installed by.
8.
System serial number.
3. Contact number.
9.
All users must be fully trained before climbing.
4. Maximum users per system.
10. Systems that are used with with and without top energy absorber and
the acceptable cable for each configuration.
5. System length.
6. Minimum distance between climbers. 11. Vertical Cable Safety System sleeve models covered by this instruction.
Figure 19:
1. Installation date.
7.
Next service date.
2. Installed by.
8.
System serial number.
3. Contact number.
9.
All users must be fully trained before climbing.
4. Maximum users per system.
10. Systems that are used with with and without top energy absorber and
the acceptable cable for each configuration.
5. System length.
6. Minimum distance between climbers. 11. Vertical Cable Safety System sleeve models covered by this instruction.
Figure 20:
1. Installation date.
8.
System serial number.
2. Installed by.
9.
All users must be fully trained before climbing.
3. Contact number.
10. Systems that are used with with and without top energy absorber and
the acceptable cable for each configuration.
4. Maximum users per system.
5. System length.
11. Vertical Cable Safety System sleeve models covered by this instruction.
6. Minimum distance between climbers. 12 Minimum Ground Clearance
7. Next service date.
13 Maximum User Weight.
