manualshive.com logo in svg

3M GMI PS200-LMP, Руководство по эксплуатации и техническому обслуживанию, Страница: 12 / 46

Поделиться
Скачать
3M GMI PS200-LMP Скачать руководство пользователя страница 12

64220, Rev. 1/April 2019

3M™ GMI™ PS200-LMP AUTO BUMP/CALIBRATION STATION

INTRODUCTION

2-2

The ABC will also charge a monitor after a bump test or calibration is complete.
A mounting bracket is supplied allowing the ABC to be secured to a workbench. 

2.2. Easy to Use

Simply insert the PS200-LMP into the ABC and close the cover to initiate automatic testing. The 

ABC uses colored LEDs to display status:
• LED 1 (Green) = ON (power)
• LED 2 (Orange) = TEST (in progress)
• LED 3 (Green) = PASS
• LED 4 (Red) = FAIL
After a successful calibration, the calibration due date on the monitor is automatically updated.

2.3. Calibration Gas and Regulators

The ABC is not supplied with calibration gas or regulators. Two gas cylinders and two regulators are 

required:
• Gas cylinder #1: Combi gas comprising methane (CH

4

) and carbon monoxide (CO)

• Gas cylinder #2: Methane (CH

4

)

• Regulator: On Demand Flow Regulator 
Tubing and barbed adapters are provided, as standard, to connect the ABC to the output of the gas 

regulators.

2.4. Supplied Software

The ABC comes with a USB memory stick, which contains the Windows-based PS200-LMP Set-

tings software that is used to:
1. Re-configure the ABC's operation.
2. Extract bump test and calibration results from the ABC for viewing and printing.
The USB memory stick also contains copies of this handbook and the Quick Operation Guide in PDF 

format.

2.5. Monitor Charging

After testing, the ABC will automatically charge the monitor. This is indicated by a battery symbol on 

the monitor's display. Charging will take up to 4 hours. On completion, a full battery symbol and 

'CHARGING COMPLETE' is displayed.
The monitor will not be damaged if left in the ABC once charging is complete.

Содержание GMI PS200-LMP















































Отзывы:

Нет отзывов