GETTING TO KNOW YOUR 3DOODLER
Actual product may vary from the image found in this document
#WhatWillYouCreate?
TM
To find great ideas for what you can create, as well as tips, tricks &
free downloadable stencils, please visit our community website at:
www.the3Doodler.com/Community
7
8
9
10
11
12
13
14
Nozzle
Extrusion Speed
Control (FAST)
Extrusion Speed
Control (SLOW)
Cooling Fan
LED Indicator
Power Cord
1
2
3
4
5
6
ALWAYS 3DOODLE IN A WELL VENTILATED SPACE
USING YOUR 3DOODLER 2.0
Step 1:
Connect your 3Doodler 2.0 to the power adapter
Connect the power adapter to the back of the 3Doodler and plug it
into a power source.
Step 2:
Turn on the pen and select
your plastic/filament
Turn the pen on by selecting the correct
heating temperature for the type of
plastic/filament you are using. Set the
slide switch to HI (“High”) for high
temperature plastics/filaments like ABS or
FLEXY, or LO (“Low”) for low temperature
plastics/filaments like PLA or WOOD.
BLUE = HI (”HIGH”)
(heating range between 230°C and
240°C; or 446°F and 464°F)
GREEN = LO (”LOW”) PLA
(heating range between
190°C and 200°C; or 374°F and 392°F)
Step 3:
Allow your 3Doodler to heat up before loading
plastic/filament
The 3Doodler takes approximately 1.5 minutes to heat up. During
that time the LED indicator will be
RED
and it will not be possible to
use the pen. Once the correct melting temperature is reached and
the pen is ready, the LED indicator will change to
BLUE
(HI) or
GREEN
(LO).
Step 8:
Power down
To safely turn the pen off, move the sliding switch to the OFF
position . Allow the pen to cool completely before storing.
Otherwise, please press one of the
extrusion buttons and wait for the
3Doodler to heat up again.
2.
Hold down
BOTH
the
FAST
(3) and
SLOW
(4) extrusion buttons at the
same time. The LED indicator (5) will
flash.
3.
When the plastic/filament stops
moving in reverse you may gently
take it out from the back of the pen .
5
2
3
Step 4:
Load the pen
Load the plastic/filament into the plastic loader at the back of
the pen, feeding it down the length of the 3Doodler until you feel it
gripped by the gears inside the pen.
NOTE:
After 5 minutes of inactivity the 3Doodler’s heating
system will automatically power down. You will need to
press one of the buttons OR toggle the power switch off
and then on again to continue use.
Note: For those of you who are curious, the distance between
the gearbox and the nozzle is under an inch.
NOTE:
Upon resumption of continuous flow, the extrusion
speed will change depending on which extrusion button
(FAST or SLOW) you used to pause the flow. The 10
minutes of continuous flow will restart after pausing.
NOTE:
Our 3Doodler is a
sturdy and awesome tool, but
like any mechanical device it
needs a break now and then.
We suggest giving it (and
yourself) some downtime after
2 hours of continuous use (just
a 30 minute break or so).
NOTE:
If you do not feel the plastic/filament being gripped
by the gears inside the pen, please give it a gentle
clockwise twist while pushing it down the shaft of the
3Doodler.
Note: If you have also purchased the 3Doodler JetPack
TM
you
can also connect this to the back of the 3Doodler as a power
source.
HI (“High”) = BLUE LED
indicator
LO (“Low”) = GREEN LED
indicator
Step 5:
Extrude/select your speed
Press and hold the button for the desired
extrusion speed (
FAST (3)
or
SLOW (4)
)
and wait for the heated material to
emerge from the pen tip. Releasing the
chosen speed button will cause the pen
to stop extruding the heated material.
If the pen stops and the
RED
LED
appears again, simply wait a moment for
2
3
Step 7:
Unloading/reversing your plastic/filament
To unload the plastic:
1.
Ensure that the device is still at the correct temperature required
for the type of plastic/filament being used:
Step 6:
Double Click for Continuous Flow
PRO-TIP:
Optimize your melt
temperature. Using the mini-screw
driver , tweak your 3Doodler’s melt
tempe/- 5°C, for minor flow
adjustments and expertly consistent
Doodles. To do this, insert the mini
screw driver into the potted
Temperature Adjuster on the control
panel.
Turn the mini screw driver
clockwise to increase the melt
temperature, or anti-clockwise to
decrease the melt temperature.
If the plastic/filament is not extruding, it may be because the
existing plastic/filament (A) is too short or has fed beyond the
gearbox, and you will not be able to reverse it. Please use a new
strand of plastic/filament (B) or the Cleaning Tool to feed the
remaining plastic/filament through the pen. In order to feed the
Cleaning Tool past the gear system you will need to gently twist it
counter clockwise until you feel it move past the gears.
A
B
the LED to change to the appropriate color again (the pen is simply
returning to its optimal heating temperature).
(4) speed buttons. While holding down
either button, insert the Cleaning Tool
through the back of the pen and gently
push any any excess plastic/filament out
TROUBLESHOOTING AND CLEANING THE PEN
This marking indicates that this product should not be
disposed of with other household wastes. To prevent
possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources.
SPECIFICATIONS
Output Power: 6W
Output Voltage: 5V
Input Voltage: 5V
CARE & MAINTENANCE
For care and maintenance information, and more advice on how to
use your 3Doodler, please refer to our website:
the3Doodler.com
To troubleshoot, please visit:
the3Doodler.com/troubleshooting
LIMITED WARRANTY
For more details on your limited warranty, pleae visit:
the3Doodler.com/warranty
For 3Doodler’s Terms and Conditions and other notices please
refer to our website:
the3Doodler.com/terms-and-conditions
Patent Pending
THE 3DOODLER IS NOT A TOY FOR CHILDREN.
ADULT USE ONLY. KEEP OUT OF REACH OF CHILDREN.
Specifications are subject to change
and improvement without notice.
If the extrusion of plastic/filament has slowed down, stopped, or if
you are having trouble inserting plastic into the pen, please give the
plastic/filament a gentle clockwise twist while pushing it down the
shaft of the 3Doodler.
If this does not work, we suggest cleaning the 3Doodler. Please
follow the steps below:
2.
Start by using the nozzle removal tool
and unscrew the nozzle anti-clockwise
while the pen is hot. Please be careful not
to touch the nozzle!
3.
Once you have removed the nozzle,
hold down either the
FAST
(3) and
SLOW
2
3
8
14
of the front of the pen. In order to feed the Cleaning Tool past the
gear system you will need to gently twist it counter clockwise until
you feel it move past the gears.
4.
Turn the pen off and allow it to cool down a little, but not fully.
Screw the nozzle on clockwise a few turns, but don’t tighten it yet.
Turn the pen back on; once it’s hot and the LED is either blue or
green, tighten the nozzle with the nozzle removal tool, stopping
when you first feel resistance.
WARNING: DO NOT force the
nozzle or overtighten it, as you could irreparably damage your
3Doodler.
5.
If you are still experiencing problems extruding or suspect there
may be a blockage in your 3Doodler, please remove the
Maintenance Cover as follows:
Ensure the LED light is
BLUE
or
GREEN
before starting this
process (indicating that the pen is hot)
Using metallic tweezers, lever up the two release hooks on
either side of the Maintenance Cover
•
•
•
•
3Doodler, DoodleStand, JetPack, StrandStand, and
“#WhatWillYouCreate?” are trademarks owned by WobbleWorks,
Inc.
For more information/customer service please contact us at
Your 3Doodler can be set to
continuously extrude
plastic/filament without you
having to hold down on the
extrusion buttons. Simply
double-click
on the desired
extrusion speed (
FAST
(3) or
SLOW
(4) ) and your 3Doodler
will continuously extrude
plastic/filament for up to ten
minutes before stopping.
To stop the continuous flow of plastic/filament, simply click on either
the
FAST
(3) or
SLOW
(4) button on your 3Doodler.
To temporarily pause the continuous flow of plastic/filament, hold
down on either the
FAST
(3) or
SLOW
(4) button on your 3Doodler
and then release to resume continuous flow.
3
2
2
3
2
3
PRO-TIP:
Speed boost!
While the
3Doodler is set to continuous flow,
firmly press down on the Maintenance
Cover to slightly speed up the
extrusion of your plastic/filament.
If the nozzle is loose, please gently tighten it, stopping when you
first feel resistance, and being sure to do so while the pen is hot.
Try to extrude again.
WARNING: DO NOT force the nozzle or
overtighten it, as you could irreparably damage your 3Doodler.
BURN HAZARD.
The nozzle of the 3Doodler
and the adjoining rubber tip can become
extremely hot. DO NOT touch the nozzle or
the adjoining rubber tip, the parts near the
nozzle or the parts near the adjoining rubber
tip, or any melted plastic/filament, or you
may be severely burned! DO NOT allow the
nozzle or the adjoining rubber tip near or in
contact with flammable materials. Inform
others in the area that the unit is hot and
should not be touched. Unplug and set the
slide switch to OFF when not in use or before
storing. After use, allow the nozzle and the
adjoining rubber tip to cool completely before
storing. The hot nozzle or adjoining rubber
tip may damage painted surfaces, plastics
and cloth if left in direct contact with these
materials.
BURN HAZARD.
The Cleaning Tool can
become extremely hot. DO NOT touch the
metal part of the Cleaning Tool after using it
to clean your 3Doodler, or you may be
severely burned!
If the 3Doodler is emitting black or brown
smoke, cease using the pen immediately,
unplug the pen, allow the pen to cool, and
then store it away safely. Failure to do so will
increase the risk of fire. Please contact us
immediately at [email protected] in such
circumstances.
ADULT USE ONLY. KEEP OUT OF REACH
OF CHILDREN.
W A R N I N G
N O T I C E
SNIP THOSE ENDS!
After removing a strand/filament from the
3Doodler, cut and remove any partially
melted material at the end of your strand
before re-feeding it into the 3Doodler. This
will reduce blockages or clogging issues.
DO NOT pull plastic/filament from the back
of the 3Doodler. This will result in damage to
your pen and will void your warranty. If you
wish to reverse your plastic/filament, please
follow the instructions on page [4].
•
•
•
•
The 3Doodler should only be used with
3Doodler approved filaments or materials.
Misuse of your 3Doodler and/or use of
non-approved plastics, filaments or other
materials may result in damage to your pen
or injury to you, and will void your warranty.
Injuries to the user may include, but are not
limited to, harm sustained from inhaling
substances that are not suitable for heating;
or burns from flammable materials used in
the 3Doodler.
WARNING: DO NOT use the 3Doodler near
bathtubs, showers, basins or other vessels
containing water. This could result the in
death due to electric shock.
When switching from lower temperature
plastic/filament (such as PLA or WOOD) to
higher temperature plastic/filament (such as
ABS or FLEXY), the presence of any
residual plastic/filament in the pen’s heating
chamber may cause a slight amount of
smoke to emit from the pen. This is due to
the application of a higher melting
temperature being applied to lower melting
temperature materials.
IT’S TIME TO 3DOODLE!
You are now the proud owner of a 3Doodler 2.0. The 3Doodler puts
the power of creation in the palm of your hand and allows you to
draw objects in 3D quickly and easily!
®
3Doodler - 2.0
WARNINGS & NOTICES
ENGLISH
Remove the Maintenance Cover by hand
Ensuring that the LED light is still
BLUE
or
GREEN
, use your
tweezers to grip and pull the plastic/filament away from the
nozzle of the pen, towards the back of the pen. Once loose,
and the end of the plastic/filament is visible inside the opening
of the pen, simply pull the plastic/filament out of the opening
using your tweezers
Replace the Maintenance Cover by inserting the latched
end into the opening at an approximately 35 degree angle
(as shown in the diagram), then pinch the two sides of the
exposed end to ensure they are inside the shell of the
3Doodler, and push the back of the Maintenance Cover
down until it clicks firmly into place
•
Maintenance Cover
Cleaning Tool
ON/OFF Switch & HI/LO
Temperature Adjuster
Control Port
Plastic/Filament Loader
Mini Screwdriver
Nozzle Removal Tool
12
1.
Ensure the LED light is
BLUE
or
GREEN
before starting
this process (indicating that the pen is hot).
13
10
7
12
9
7
8
Turn nozzle
removal tool
anti-clockwise
14
3
2
B
A
X2
12
Plastic/filament
2
3
LED LEGEND:
Solid RED:
Heating up
(please wait)
BLUE:
ABS
(230°C to 240°C;
446°F to 464°F)
GREEN:
PLA
(190°C to 200°C;
374°F to 392°F)
Flashing LED:
Reversing plastic.
HI
LO
OFF
2
1
3
4
9
11
10
7
14
13
8
12
5
6
35°
clockwise twist
3
2
10
13
7
7
Plastic/filament
A-PDF Page Cut DEMO: Purchase from www.A-PDF.com to
remove the watermark
