Quick
Start
Guide
#WhatWillYouCreate?
TM
Button
Features
SLOW SPEED
Hold down on the small
button for slow.
FAST SPEED
Hold down on the big
button for fast.
DOUBLE CLICK
Constant Doodling without
holding down any buttons.
∙
Hold down button to pause
∙
Single click to stop
BOTH BUTTONS
Hold down on both buttons
to reverse your strand while the
LED flashes.
For more detailed instructions and
additional tips please see the user
manual or visit
the3Doodler.com
2. INSERT
YOUR
STRAND
Press the
fast or
slow button.
3. READY
SET
DOODLE
It will take 30 - 40
seconds for your
plastic to extrude.
1. PLUG IN
& SELECT
TEMP (HI/LO)
It will take 1 - 2
minutes for your
3Doodler to heat up.
FLEXY
ABS
PLA
WOOD
SET YOUR 3DOODLER
TO THE CORRECT
TEMPERATURE:
HI
LO
PLASTIC
TRANSITION
When switching from a HI temp plastic (like ABS) to a
LO temp plastic (like PLA), run the pen on the HI
setting until the HI temp plastic is fully extruded
(you'll see the plastic color change!). Then switch the
pen to the LO temp setting.
After you have finished using your 3Doodler, remove
any remaining plastic.
BEFORE SWTICHING
FROM HI TO LO
@3Doodler
JOIN THE COMMUNITY
Discover and share instant inspiration (and hundreds
of free stencils!) with our global community at:
the3Doodler.com/community
Inspiration
In a
Jam?
If it’s still not working then follow
the step by step instructions in
the user manual or message us
at
or visit
our YouTube channel at:
youtube.com/3Doodler
PUSH FIRST
TURN OVER >>>>>>
Pro Tips
NOZZLE REMOVAL
Make sure the pen is
HOT (blue or green
LED) before trying to unscrew the nozzle. When
screwing the nozzle back on don’t force it.
TEMPERATURE ADJUSTMENT
Manual temperature optimization for minor flow adjustment
and expertly consistent 3Doodles. Turn it 90° to the
right to crank up the heat, or 90° to the left to turn it down.
WELD PLASTIC
You can join 3Doodled pieces by touching the hot tip of the
3Doodler to both parts to melt them together while extruding.
Don’t worry about rough edges; you can trim those later.
Nozzle Removal Tool
(included)
Use the mini screwdriver
(included)
Snip Snip
Keep it clean. Snip your ends to avoid
any unnecessary jams in your 3Doodler.
THOSE ENDS!
Plastics &
Accessories
Choose from 60+ vibrant plastic colors. Transform
your Doodling with our latest accessories including
the Nozzle Set.
Nozzle removal tool
with 6 new nozzles
For more accessories please visit
http://the3doodler.com/store/
The perfect place
to store your 3Doodler
For more information,
customer service, repairs, or
warranty inquiries please contact
us at
Light red
whilst
Doodling?
Your 3Doodler is functioning
normally. The red light / pausing
is caused by the pen heating up
to stay at optimal temperature.
The 3Doodler needs to pause
while doing this. Wait a few
seconds and keep Doodling!
DON’T FRET
Plastic
Curling?
Push your pen firmly into the paper,
allow the plastic to extrude for a
couple of seconds, and then lift the
pen up off the paper.
GET A GRIP
Trouble
Reversing?
Hold down on BOTH extrusion buttons at the
same time to reverse the plastic strand.
If your strand is too short to fully reverse, you will
not be able to retrieve it. If this happens turn the
pen on and wait for the pen to heat up (the LED
light will change to Blue or Green).
Remove the nozzle with the spanner provided in
the box.
Now take the unblocking tool (or a straightened
paperclip) and feed it into the nozzle end of the
pen to dislodge any blocked plastic. The
dislodged plastic should shake free from the
back of the pen. If it doesn’t shake free, from the
back of the pen. If it doesn’t shake free, please
proceed to remove the maintenance cover to
clear out the plastic.
Replace the nozzle while the pen is hot and then
try the pen again - don’t over-tighten the nozzle
or apply excess force.
1.
2.
3.
4.
5.
