3DHISTECH PANNORAMIC SCAN RX 1.1 Скачать руководство пользователя

Страница: 154 / 165

PANNORAMIC® SCAN RX 1.1

TROUBLESHOOTING AND MAINTENANCE

NOVEMBER 18, 2021

153

FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES.

Use an open-end wrench (W/F 10)

(5)

to turn the screws

(3)

on the lateral sides of the

Pannoramic® SCAN RX by 90° anticlockwise, proceeding pairwise

(B)

. Use both hands

to take cover

(1)

carefully off upwards.

Caution!

Use caution to prevent contact between the safety rails and the scan camera as you take
cover off.

Turn eccentric screw at the front of the base plate by 90° anticlockwise and use both
hands to carefully raise and take cover

(2)

off.

After finishing the necessary maintenance or repair work, put the covers (cover

(2)

first, then cover

(1)

) back into place and lock them in their positions. To do this, turn

the eccentric screws clockwise

(A)

Caution!

Make sure that no cables of the scan camera are squeezed as you replace the covers.

9.5.2

Removing a slide

If a slide got jammed or has suffered breakage during the process of digitization, stop the
process and, if possible, move the slide holder to a position where the slide can be easily
removed by clicking the

Emerg. position

button (see

Emergency slide operations

chapter

6.1 Settings

Warning!

Crush hazard! Before you remove a jammed slide, cancel

the running digitization process,

terminate the software session and turn the power off.

Caution!

Any manipulation performed on a mechanical component must be followed by a complete
device initialization routine (software restart).

Содержание PANNORAMIC SCAN RX 1.1






































































































































































Результаты поиска

Содержание PANNORAMIC SCAN RX 1.1

Отзывы:

Похожие инструкции для PANNORAMIC SCAN RX 1.1

Бренды по названию

Популярные бренды

3DHISTECH PANNORAMIC SCAN RX 1.1, Руководство пользователя

Результаты поиска

Содержание PANNORAMIC SCAN RX 1.1

Отзывы:

Похожие инструкции для PANNORAMIC SCAN RX 1.1

Бренды по названию

Популярные бренды