3DHISTECH PANNORAMIC SCAN RX 1.1 Скачать руководство пользователя

Страница: 152 / 165

PANNORAMIC® SCAN RX 1.1

TROUBLESHOOTING AND MAINTENANCE

NOVEMBER 18, 2021

151

FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES.

Virtual slides show poor stitching in Viewer.

•

Scan camera is not properly adjusted (for example, due to loose fixture)

•

Contact 3DHISTECH Service for support.

Slide is often positioned incorrectly.

•

Guiding fault in transport system

•

Check if faulty positioning disappears after the selection of a different type of
magazine (for example, universal magazine).

•

Contact 3DHISTECH Service for support.

Digitization process is extremely slow.

•

Extended focusing

option is activated.

•

Deactivate the

Extended focusing

option if not required.

•

Z-stack

option is activated.

•

Deactivate the

Z-stack

option if not required.

Image is out of focus. (in Manual mode)

•

Focus range limit is activated.

•

Deactivate the

Limiting focus range

option.

•

Focus range setting is incorrect

•

Change focus range setting.

All individual images show a shading effect.

•

Algorithm failed to find empty image fields

•

Capture a reference image with a blank slide.

9.4.1

Fluorescent applications (optional)

The switching of the Lumencor SPECTRA 6 cannot be triggered, despite triggering connection
through the camera.

•

Contact 3DHISTECH Service for support.

No suitable exposure time can be found. Signal is too weak.

Содержание PANNORAMIC SCAN RX 1.1






































































































































































Результаты поиска

Содержание PANNORAMIC SCAN RX 1.1

Отзывы:

Похожие инструкции для PANNORAMIC SCAN RX 1.1

Бренды по названию

Популярные бренды

3DHISTECH PANNORAMIC SCAN RX 1.1, Руководство пользователя

Результаты поиска

Содержание PANNORAMIC SCAN RX 1.1

Отзывы:

Похожие инструкции для PANNORAMIC SCAN RX 1.1

Бренды по названию

Популярные бренды