manualshive.com logo in svg

3DHISTECH PANNORAMIC SCAN RX 1.1, Руководство пользователя

Поделиться
Скачать
3DHISTECH PANNORAMIC SCAN RX 1.1 Скачать руководство пользователя страница 10

PANNORAMIC® SCAN RX 1.1 

NOTES REGARDING OPERATIONAL SAFETY 

 

NOVEMBER 18, 2021 

9

 

FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES.

 

Notes Regarding Operational Safety 

The below chapter 

of this User’s Guide contains information and warnings of a kind that must be 

followed by owner/operator personnel. 

Warning and advisory symbols which are used on the base unit of the Pannoramic® SCAN RX and 
in chapter 

1.1.3 Warning and Information Labels

 have the following meanings: 

 Warning! 

 Disconnect mains plug! Remember to unplug the power cord before you open the 

Pannoramic® SCAN RX main unit for maintenance. 

 Crush hazard! There is crush hazard in the movement area of the slide insert during 

operation. Make sure not to reach with your hands into the instrument to avoid the risk of 
crushing your fingers. Please note that the digitizing process has to be interrupted and the 
slide magazine moved via software to the output position before removing it.

 

 

The Pannoramic® SCAN RX, including any of its original accessory components, should not be 
operated in any other way than described in chapter 

1.1.1 Intended Use

. 

 

Any of the following notes should be strictly observed: 

 Warning! 

If operating the device other than specified by the manufacturer, the level of safety will 
decrease. 

 

 Warning! 

Insert the power cord plugs only into a grounding outlet. The protective action must not be 
rendered ineffective by extension cables without protective conductor. The Pannoramic® 
SCAN RX has a built-in protection which must not be rendered ineffective by extension 
cables without protective (earth-ground) conductor. 

 

Содержание PANNORAMIC SCAN RX 1.1






































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды