3D Systems PostCure 1050 Скачать руководство пользователя страница 64

Страница: 64 / 68

ISSUE DESCRIPTION

CUSTOMER TROUBLESHOOTING

STEPS

NI2

Unable to set static IP address from

machine

1. Please contact your network

administrator to ensure you have a

DHCP server and that it is set up

correctly.

2. Ensure that DHCP is enabled in the

machine settings.

NI3

Cannot connect to Internet via USB

dongle

Internet connection via USB is not

available on this machine.

NI4

I am not sure if my network cable is bad Use the cable on another device, such as

a computer, to test it.

8.3 PostCure 1050 Firmware Issues

This page describes troubleshooting firmware issues with the PostCure 1050 that will not show an error on the touch screen.

ISSUE DESCRIPTION

CUSTOMER TROUBLESHOOTING

STEPS

FI1

GUI out of sync/lagging

1. Flip the standby switch to Standby.

Unplug the machine. Wait 30

seconds, plug it back in, and flip the

standby switch to "on." This will reset

any background tasks that might be

making the machine slower.

2. If item 1 does not fix the issue,

contact 3D Systems Service.

3D Systems, Inc.

p/n 40-D177, Rev. A

Содержание PostCure 1050





































































Результаты поиска

Содержание PostCure 1050

Отзывы:

3D Systems PostCure 1050, Руководство пользователя, Страница: 64 / 68

Результаты поиска

Содержание PostCure 1050

Отзывы: