manualshive.com logo in svg

3D Systems PostCure 1050, Руководство пользователя, Страница: 61 / 68

Поделиться
Скачать
3D Systems PostCure 1050 Скачать руководство пользователя страница 61

8

  POSTCURE 1050 TROUBLESHOOTING

There are unique situations you may encounter when operating the PostCure 1050. These situations, and their solutions, are

described in the following table.

Note: Unless troubleshooting steps require the PostCure 1050 to operate, shut down the unit and unplug it

before performing troubleshooting steps.

8.1  PostCure 1050 Hardware Issues

This page describes troubleshooting hardware issues with the PostCure 1050 that will not show an error on the touch screen.

WEAR 100% NITRILE GLOVES WHENEVER HANDLING green parts

#

ISSUE DESCRIPTION

CUSTOMER TROUBLESHOOTING STEPS

HW1

Part is not fully cured in its entirety 1. A fully cured part will have no discernible areas of tackiness or oiliness.

Ensure you used the correct material recipe for the resin with which you

printed.

a. Yes, I used the correct material recipe. Go to Step 2.
b. No, I used an incorrect material recipe. Go the Cure Job History screen

and observe the settings and duration for that job.

Note: Different recipes use different light intensities,

a different light spectrum, and different temperature

profiles. For best results, it is recommended to use

the correct material recipe and customize the material

recipe by adjusting the cure time, light intensity, or cure

temperature to achieve custom curing results. If parts

are not fully cured, it is recommended to add additional

curing time to the curing recipe before adjusting other

parameters.

1. If the curing time used was greater than the curing time

recommended for the material, the part is likely over-cured and will

not have the desired mechanical properties. Discard the part at your

discretion.

2. If the curing time used was less than the curing time recommended

for the material, customize your material recipe to cure for the

remaining time needed.

3. If you accidentally selected a material recipe for a material that

performs a thermal curing cycle, the part is likely over-cured and will

not have the desired mechanical properties. Discard the part at your

discretion.

2. Ensure you properly cleaned the part, according to your printer's Post-

Processing Guide, and performed a drying cycle. Customize your material

recipe to cure in increments of five minutes until part is fully cured. Also,

some materials are more prone to be tacky than others and may require

special cleaning/drying steps to minimize tackiness after post curing.

3D Systems, Inc.

58

p/n 40-D177, Rev. A

Содержание PostCure 1050





































































Отзывы:

Нет отзывов