manualshive.com logo in svg
background image

 

1

3 D  H O B B Y S H O P . C O M

 

 

Assembly Manual  -  

Extra SHP 47”

 

 

 

Thank you for purchasing this 3DHobbyShop ARF RC aircraft.  If you have any issues, questions, 
concerns or problems during assembly, please contact our tech department at: 

 

[email protected]

 or 1-830-990-6978 10am-5pm Central M-F 

 
We highly recommend 

www.RCGroups.com

 as a good source for RC tips, tricks, and information. 

 

SAFETY in Assembly 

 
During assembly of this aircraft, you will be asked to use sharp knives and hobby adhesives.  Please 
follow all safety procedures recommended by the manufacturers of the products you use, and always 
follow these important guidelines: 
 
ALWAYS protect your eyes when working with adhesives, knives, or tools, especially power tools.  Safety 
glasses are the best way to protect your eyes. 
 
ALWAYS protect your body, especially your hands and fingers when using adhesives, knives, or tools, 
especially power tools.  Do not cut toward exposed skin with hobby knives.  Do not place hobby knives on 
tables or benches where they can roll off or be knocked off.   
 
ALWAYS have a first-aid kit handy when working with adhesives, knives, or tools, especially power tools.   
 
ALWAYS keep hobby equipment and supplies out of the reach of children. 
 

IMPORTANT NOTE

 – We strive to provide the absolute best-quality ARF aircraft on the planet.  However, 

the ultimate success or failure of this aircraft is dependent upon proper assembly by you 
 

SAFETY in Flying 

 
SAFETY NOTICE:  This is NOT a toy!  It is a very high-performance RC airplane capable of high speeds 
and extreme maneuvers.  It should only be operated by a competent pilot in a safe area with proper 
supervision.   
 
ONLY fly your aircraft in a safe, open area, away from spectators and vehicles–and where it is legal to fly. 
 
NEVER fly over an unsafe area, such as a road or street. 
 
NEVER fly near overhead power or utility lines.  If your airplane ever becomes stuck in a line or a tree DO 
NOT attempt to retrieve it yourself.  Contact the authorities for assistance in retrieving your aircraft.  
Power lines are DANGEROUS and falls from ladders and trees CAN KILL! 
 
Never fly too close to yourself or spectators.  Spinning propellers are DANGEROUS! 
 
Never run your motor inside a house or building with the propeller attached – Remove the prop for safety. 
 
Always fly within your control. 
 
Always follow manufacturer’s instructions for your radio system. 
 

Содержание Extra SHP 47"





















Отзывы: