3Com VCX V7000 страница 424 Скачать руководство пользователя | Manualshive

Страница: 424 / 488

background image

422

A

PPENDIX

C: R

EPLACING

A

F

AILED

D

ISK

ON

A

VCX S

ERVER

You can obtain more or less information by using one of these
commands:

vcx-raid-status --verbose

vcx-raid-status --short

Disk Drive Location

On an IBM x306m server, Disk drive 0 is located in the left slot as you face
the front of the server. Disk drive 1 is located in the right slot.

On an IBM x345 or x346 server, Disk drive 0 is located in the upper slot as
you face the front of the server. Disk drive 1 is located in the lower slot.

On a 3Com V6000 server, Disk drive0 is located in the left slot as you face
the back of the server. Disk drive 1 is located in the right slot.

Replacing a RAID Disk

To replace a failed RAID disk:

1

Shut down the server on which the disk failure has occurred.

2

Remove and discard the failed disk drive.

3

If the failed disk was drive 0, you must move the disk that is in the drive 1
slot to the drive 0 slot. Otherwise, skip this step.

CAUTION:

The working disk drive must be located in the drive 0 slot

prior to starting the server. If you leave the working disk in the drive 1 slot
and insert the replacement disk in the drive 0 slot, the server cannot be
properly started.

4

Insert a replacement disk into the drive 1 slot.

The replacement disk can be larger than the failed disk. Any additional
storage space on the replacement disk will not be used, however.

5

Restart the server.

6

After the system is running, log in as root and enter this command:

vcx-raid-recover

To view the status of the recovery process, you can enter one of the

vcx-raid-status

commands that are listed in

“Identifying the Failed

earlier in this appendix.

CAUTION:

Do not

shut down or restart the server until the RAID recovery

process has been completed. Wait until the

vcx-raid-status

command

returns the message

All RAID disks are operational.

«
...
422
423
424
425
426
...
»

Содержание VCX V7000









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VCX V7000

Бренд: switel Страницы: 4

Бренд: Telesis Страницы: 11

Бренд: Alcatel Страницы: 96

Бренд: Opel mobile Страницы: 76

BLACKVIEW GBV7000 Pro

Бренд: Iget Страницы: 47

Бренд: Yezz Страницы: 68

Бренд: KARBONN Страницы: 33

Бренд: Sagem Страницы: 84

Бренд: Samsung Страницы: 40

Бренд: Samsung Страницы: 26

JetSet SCH-R550 Series

Бренд: Samsung Страницы: 152

Бренд: Samsung Страницы: 124

Бренд: Samsung Страницы: 174

ALIGATOR S6500 Senior

Бренд: ADART COMPUTERS Страницы: 16

Бренд: Zte Страницы: 79

Бренд: Innovall Groups Страницы: 40

6030 - Cell Phone - GSM

Бренд: Nokia Страницы: 189

Бренд: Panasonic Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды