manualshive.com logo in svg

3Com 3Com SuperStack 3 Switch 3800 Family, Руководство пользователя

Поделиться
Скачать
3Com 3Com SuperStack 3 Switch 3800 Family Скачать руководство пользователя страница 167

D

T

ECHNICAL

 S

UPPORT

3Com provides easy access to technical support information through a 
variety of services. This appendix describes these services.

Information contained in this appendix is correct at time of 
publication. For the very latest, we recommend that you access 3Com 
Corporation’s World Wide Web site as described below.

Online Technical 
Services

3Com offers worldwide product support 24 hours a day, 7 days a 
week, through the following online systems:

■

World Wide Web site

■

3Com Bulletin Board Service (3ComBBS)

■

3ComFacts

SM

 automated fax service

■

3ComForum on CompuServe

®

 online service

World Wide Web Site

Access the latest networking information on 3Com Corporation’s World 
Wide Web site by entering our URL into your Internet browser:

http://www.3Com.com/

This service features news and information about 3Com products, 
customer service and support, 3Com Corporation’s latest news releases, 

NetAge

 Magazine, and more.

3Com Bulletin Board

Service

3ComBBS contains patches, software, and drivers for all 3Com 
products, as well as technical articles. This service is available via 
modem or ISDN 24 hours a day, 7 days a week. 

Access by Analog Modem

To reach the service by modem, set your modem to 8 data bits, 
no parity, and 1 stop bit. Call the telephone number nearest you:

SW3800.BK  Page 1  Tuesday, May 5, 1998  5:20 PM

Содержание 3Com SuperStack 3 Switch 3800 Family























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды