Thank you for your purchase of this product.
Before attempting to connect or operate this
product, please read these instructions completely.
The above drawing is for reference only.
MODEL:
OUTDOOR FIXED LENS
IP IR DOME CAMERA
2CU-X241-IP
2.0 Mega-Pixel
1.Installation and maintenance should be carried out by professional personnel as per
relative regulations. All electrical work must obey the latest electrical regulations,
fire regulations and relevant regulations. Check whether the accessories of the unit
are complete according to packing list and confirm whether the place and method of
installation is in accord with required, if not, please contact your supplier. Please
use this product in required environment.
2.This IP camera is designed for outdoor use.
3.After re-installation or repair, you need to measure the resistance between the
circuit and shell to check whether the insulation is good and ensure there is no
short-circuit between the circuit and shell.
4.Confirm there is enough place to contain the product and its structural components.
Confirm the ceiling, wall and bracket for installation can take the total weight of the
product and its structural components, and materials used to support the weight
can sustain four times the weight of the product.
5.Please check the product package well. You can send the IP camera to factory with
that package if there is any problem that needs to service.
INSTALL PREPARATION
PACKAGE CONTENTS
1. IP CAMERA.........................................................................................................1pcs.
2. CD.......................................................................................................................1pcs.
3. MOUNTING TEMPLATE STICKER.........................................................................1pcs.
4. SCREW...............................................................................................................3pcs.
5. WALL PLUG........................................................................................................3pcs.
FEATURES
1.Do not attempt to disassemble the camera.
2.Handle the camera with care.
3.The installation should be made by qualified service personnel or system installers.
4.Do not use strong or abrasive detergents when cleaning the camera body.
5.Clean the CMOS faceplate with care.
6.Never face the camera towards the sun.
7.Use the camera at temperatures within –10 °C to +50 °C, and humidity below 90 %
RH and the storage temperatures should be within –20 °C to +60 °C and humidity
below 20% to 80 % RH.
8.Please operate the camera within the specified power source ratings. Avoid
connections during a lightning storm. Otherwise, an electric shock may be caused.
PRECAUTIONS
!
DO NOT OPEN
RISK OF ELECTRIC SHOCK
CAUTION
DO NOT REMOVE COVER (OR BACK),NO
USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
TO REDUCE THE RISK OF ELECTRIC SHOCK,
CAUTION
!
The lightning flash with arrowhead
symbol, within an equilateral
triangle, is intended to alert the user
to the presence of uninsulated
dangerous voltage within the
product’s enclosure that may be
sufficient magnitude to constitute a
risk of electric shock to a person.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in literature accompanying the appliance.
CAUTION
1/2.5” Sony Exmor Progressive Scan Sensor
2.0 Megapixel Resolution (1936*1097)
Image Resolution: 1080P (1920x1080)/720 (1280x720)/D1 (704x576)/CIF (352x288)
Frame Rate 1080P@25fps; 960P@25fps; 720P@25fps
Dual Stream: Support Main Stream and Sub-stream
3.6mm (3.0 Mega) Fixed Focal Lens
H.264 and MJPG Compression
255 CH Free Admin Vision NVR& CMS Software
Support Admin Vision DDNS
Support ONVIF Ver.2.0 or 3rd.Party NVR/HVR on Request
True Day/Night with ICR on Sensor
Support Protocol TCP/IP, HTTP, DHCP, DNS, DDNS, PPPoE, SMTP, etc.
Power Supply: 12VDC & PoE Input
Support D-WDR/Motion Detection/BLC/Image Setup/ Day/Night/AGC/Smart IR,
etc.
Lowest Power Consumption
Lowest Heat on Board for Long Life of Camera
30 Meters Visual Distance with 36pcs LED (14mil Oblong IR LED Supreme Night
Visibility & Uniform IR with Proprietary Split Beam Lens on LED)
CAMERA CONNECTION
Network Interface
Connect the network interface using RJ 45 network cable. It shows working when the
network indicator is on.
12 V DC Power Supply
Connect the 12 Volt DC power using DC Jack. Please make sure the polarity is correct.
Incorrect polarity may cause malfunction and/or damage to the camera.
Wiring Precautions
Do not bend the coaxial cable into a curve whose radius is smaller than 10 times the
cable’s diameter.
Never staple the cable even if with circular staples. Otherwise impedance mismatching
will occur.
