2N VoiceBlue Next страница 26 Скачать руководство пользователя | Manualshive

Страница: 26 / 117

background image

26

2N TELEKOMUNIKACE a.s., www.2n.cz

®

2.5 VoiceBlue Next Connection to VoIP

Since

communicates using the SIP only, this subsection outlines

2N VoiceBlue Next

®

solutions for its interconnection with networks working with the H.323 signalling
protocols.

can be used either in the Point-to-Point or

2N VoiceBlue Next

®

Point-to-Multipoint mode with the SIP Proxy server.

SIP / H.323 Interconnection

SIP-based  devices  cannot  communicate  with  H.323.supporting  devices  directly,  but
through a SIP/H.323 gateway. This gateway transfers signalling messages from/to the
protocols. Using the RTP for multimedia data transmission, the SIP and H.323 protocols
can  go  on  communicating  directly  when  the  SIP/H.323  gateway  connection  is
established.  Thus,  the  SIP/H.323  gateway  helps  integrate

into

2N VoiceBlue Next

®

the existing H.323 environment.

Point-to-Point Configuration

2N VoiceBlue Next

®

can communicate with just one SIP VoIP phone or device (a

VoIP gateway, e.g.) in the PTP (Point-to-Point) mode. The IP address of the opposite
party is always selected as the Proxy server IP address in

for

2N VoiceBlue Next

®

this mode.

The

PTP configuration is often used for testing purposes before

2N VoiceBlue Next

®

implementation into the VoIP network. Refer to the figure below for the PTP scheme.

Tip

If you set the incoming SIP Proxy IP address to '0.0.0.0' in the

2N

®

configuration, the GSM gateway will receive calls from

VoiceBlue Next

any VoIP device.

«
...
24
25
26
27
28
...
»

Содержание VoiceBlue Next






















































































































Отзывы:

Нет отзывов

Похожие инструкции для VoiceBlue Next

Бренд: Ubee Страницы: 114

Бренд: Ubee Страницы: 105

Бренд: Ubee Страницы: 96

Бренд: Ubee Страницы: 96

Бренд: CHERUBINI Страницы: 16

Бренд: CYP Страницы: 12

NFS/DFS Secure Gateway

Бренд: IBM Страницы: 67

Modular IoT Gateway

Бренд: Volansys Страницы: 26

Бренд: DAE Страницы: 2

Бренд: Fife Страницы: 48

Бренд: Sangoma Страницы: 4

Бренд: RFM Страницы: 31

Бренд: Technicolor - Thomson Страницы: 52

OmniAccess 8550

Бренд: Alcatel-Lucent Страницы: 98

Бренд: CPS Страницы: 23

Бренд: ECKELMANN Страницы: 58

STHC-B-ISG02DB-03

Бренд: daviteq Страницы: 25

Бренд: TECOM Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды