2N Netstar Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 282

2N Netstar Скачать руководство пользователя страница 43

43

3.2 Cornet

Cornet is a digital virtual port for the StarPoint key phones with proprietary signalling
(UPN interface). The Stack tag provides limited configuration capacities only. The
parameters are divided into logical sections according to their respective functions. For
the StarPoint configuration parameters refer to the Softphone subtag of the Properties
tag. For more details on Softphone extensions refer to Chapter

.

Setting Properties

Virtual port status

The upper menu field displays information on the stack type and its current status
including information on the L1 and L2 states, increased bit error rate or
nonsynchronous L1.

Digital interface parameters

Interface type

– the parameter cannot be configured. It only shows the type of

interface.

Interface mode

– this parameter is set to NT and cannot be reconfigured. Thus,

cross–connecting lines cannot be made using these ports.

Bus mode

– this parameter is always set to PTP and cannot be reconfigured.

This port is used for one terminal only.

Enabled channels

– use this parameter to enable selected interface channels. If

none is enabled, the interface cannot be used and behaves as if it was busy.

Keep L1 active

– check this option to make the PBX keep the interface active

automatically.

Inactive L1 as error

– use this option to activate a caution about the first layer

being inactive. This is indicated by a red exclamation mark on the port in the

menu and a red text in the upper stack status field.

Hardware – Boards

Set BER

– select BER as error to enable acceptable BER range parameters. If the

BER rate gets over the

, a red exclamation mark appears on the

BER error level

port in the

menu and a red text is displayed in the port

Hardware – Boards

status field. This error status gets changed after the BER value falls below the

. The interval between these two values represents hysteresis. The

BER OK level

BER values are entered in an exponential format (e.g. 3e–5 means 3 errors in
100,000 bits).

Master terminal

Type

– shows the type of the StarPoint terminal connected.

Firmware

– shows the current firmware version of the terminal connected.

Extenders

– shows information on the active extenders of the terminal

connected.

Slave terminal

Type

– shows the type of the StarPoint terminal connected.

Firmware

– shows the current firmware version of the terminal connected.

Extenders

– shows information on the active extenders of the terminal

connected.

«
...
41
42
43
44
45
...
»

Содержание Netstar



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды