Zummo Z22 Technical Instructions Download | Manualshive

Page: 1 / 13

background image

011319-03

1

Technical instructions

Z22

TECHNICAL INSTRUCTIONS FOR JUICE EXTRACTOR Z22

INDEX:

1.-

Disassemble machine

2.- Dismantling and change motor
3.-

Closing machine

4.-

Grating disc change

5.-

Electric diagram

6.-

Troubleshooting

1.- Disassemble machine

1.1.

This juicer machine has a metallic locking arm, that allows locking the machine up while

working. When the locking arm is unlocked, turns a micro-switch off and it makes that the
juicer doe

sn’t works and we can work safety. (Otherwise we should disconnect the mains

before doing anything with the machine)

1
2
3
...
»

Summary of Contents for Z22














Reviews:

No comments

Related manuals for Z22

Brand: Zanussi Pages: 24

Brand: Zanussi Pages: 20

Brand: Zanussi Pages: 7

MASTERCHEF EXECUTIVE TERMOROBOT WiFi

Brand: Sam Cook Pages: 42

Brand: Randell Pages: 11

Brand: Schou Pages: 37

Brand: German pool Pages: 24

Brand: EDM Product Pages: 21

Brand: fizzics Pages: 12

Brand: Salton elite Pages: 7

Brand: Ivation Pages: 2

Brand: TEFAL Pages: 12

Brand: Zelmer Pages: 38

Brand: Qi Aerista Pages: 20

Brand: Magic Chef Pages: 10

Brand: Waring Pages: 8

Brand: McCall Pages: 2

Brand: Sencor Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands