ATTENTION: READ CAREFULLY BEFORE ATTEMPTING TO INSTALL OR OPERATE YOUR PUMP. PROTECT YOURSELF AND OTHERS
BY OBSERVING ALL SAFETY INFORMATION AND ADDITIONAL INSTRUCTIONS INCLUDED WITH EQUIPMENT. FAILURE TO COMPLY
WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN FOR FUTURE REFERENCE.
SECTION: 6.10.143
FM2340
0711
Supersedes
0110
INSTALLATION INSTRUCTIONS
These installation instructions are applicable for Model 370-0002 Aeration/Fountain Pump only.
This pump system is designed for decorative use and can improve water aeration.
PREINSTALLATION CHECKLIST - ALL INSTALLATIONS
AERATION/FOUNTAIN PUMP MODEL 370-0002
SEE BELOW FOR LIST OF WARNINGS
1
.
Make certain that the power source conforms to the requirements of
the equipment as stated on the product nameplates and wire motor for
correct voltage. See motor nameplate.
2.
Periodically inspect the pump for damage and perform routine
maintenance as required.
3.
The maximum temperature of the pumped liquid must not exceed 120
°
F.
4.
Supply voltage must be with in +/- 10% of nameplate voltage. Incorrect
voltage can cause fire or seriously damage motor and voids warranty. If
in doubt, consult a licensed electrician.
REFER TO WARRANTY ON PAGE 2.
SEE BELOW FOR LIST OF CAUTIONS
Product information presented
here reflects conditions at time
of publication. Consult factory
regarding discrepancies or
inconsistencies.
MAIL TO: P.O. BOX 16347 • Louisville, KY 40256-0347
SHIP TO: 3649 Cane Run Road • Louisville, KY 40211-1961
(502) 778-2731 • 1 (800) 928-PUMP • FAX (502) 774-3624
visit our web site:
www.zoeller.com
®
Your Peace of Mind is Our Top Priority
®
1. Make sure that the pump is plugged into a properly grounded
electrical receptacle.
Use an Underwriters Laboratory listed circuit
analyzer to test for proper installation of the circuit and ground. Any service
to circuits or receptacles should be conducted by a qualified licensed
electrician.
2.
Do not remove the ground pin from the plug under any circumstances.
If the ground pin is damaged, replace the power cord or plug before use.
3.
All electrical installations must conform to the requirements of the National
Electric Code and all local codes.
4.
System furnished with a 100 ft. power cord with 3-prong GFCI plug; must
connect to properly grounded receptacle of grounding type. Do not
remove ground pin on plug. Do not extend the cord length by splicing
or with an extension cord.
5.
Disconnect power before servicing the pump or motor by unplugging
the unit from the outlet.
6.
Do not touch the motor when operating and allow the motor
to cool before touching.
7.
Pump is built to handle clear water only; it is not designed to handle water
containing sand, silt, or other abrasives.
8.
Do not use to pump flammable or explosive fluids such as
gasoline, kerosene, fuel oil, etc. Do not use in flammable
and/or explosive atmospheres.
9.
Do not use this product in hazardous environments or
anywhere a spark could potentially ignite explosive gases.
10.
Do not handle this product with wet hands or while standing in water
or on a wet or damp surface.
11.
Units are supplied with an automatically resetting thermal overload
device and can restart without warning.
12.
Provide a means of pressure relief if the pump discharge
can be shut off or obstructed. Pumps operating against a
closed discharge can create very hot pumped liquid, which
can cause burns.
13.
“No swimming” and/or warning signs should be posted per state and
local codes. Please affix included warning label to power receptacle
or junction box.
14.
Do not ground to a gas supply line.
15.
Protect the power cable from coming in contact with sharp objects, oil,
grease, hot surfaces, or chemicals. DO NOT kink the power cable. If
damaged, replace immediately.
16.
According to the state of California (Prop 65), this product contains
chemicals known to the state of California to cause cancer and birth
defects or other reproductive harm.
17.
NEVER leave the control box, fused disconnect switch or cover open
(either partially or completely) when not being worked on by a competent
electrician.
18.
Water leaving nozzle is at a high velocity and can cause bodily injury
if contact is made.
19.
Never examine, make wiring changes, or touch the motor before
disconnecting the main electrical supply switch. The thermal device
may have opened the electrical circuit. All motors should be equipped
with a correctly fused disconnect switch to provide protection. Consult
local or United States National Electrical Codes for proper fuse protection
based on motor data chart.
20.
GFI plug must be oriented with cord coming out of the bottom and
protected from direct rainfall.
021766
