Zigbee Heating Thermostat
ROB
_
200-040-0
Function introduction
Important:
Read All Instructions Prior to Installation
Front side
1. Product Data
F
TIME/SHIFT button, to set
time schedule of the
device quickly and move
the cursor
Function button, to
confirm, save setting
Mode button, to switch
operation modes and quit
Move up and move down
buttons
LED Display
59 mm
80 mm
59 m
m
80 m
m
10 mm 10 mm
31 mm
Back side
NTC
L L N N
AC Power input
Floor temp sensor
Output
Home Interface
SR-ZG9092A
Radio Frequency
Input Voltage
Output Voltage
Max Load
Max Current
Power Consumption
Ambient Temperature
Set Temperature Range
Hysteresis
Floor sensor type
Control Type
Approvals
1. NTC/10K B(25/50
℃
)=3950 (default)
2. NTC/15K B(25/50
℃
)=3950
3. NTC/50K B(25/50
℃
)=3950
4. NTC/100K B(25/50
℃
)=3950
5. NTC/12K B(25/50
℃
)=3950
Control type means which temperature sensor the device refers to
when it adjust temperature.
Room sensor
: adjust temperature refers to room temperature
(factory default type).
Floor sensor
: adjust temperature refers to floor temperature.
Room+Floor sensor
: adjust temperature refers to both room
temperature and floor temperature.
CE
,
LVD
: EN 60730-1:2016;A1, EN IEC 60730-2-9:2019;A1
EMC & RF
: EN IEC 61000-3-2:2019, EN 61000-3-3:2013+A1:2019,
EN 60730-1:2016+A1:2019, EN 60730-2-
19:2019+A1:2019+A2:2020, EN 50663:2017;ETSI EN 301 489-
1V2.2.3, ETSI EN301 489-3V2.1.1
ETSI EN300 220-1 v3.1.1., ETSI EN300 220-2 V3.2.1
RED certificate
: 2014/53/EU
•
The Zigbee HVAC controller is a wireless thermostat for heating system, which complies to Zigbee 3.0
wireless protocol standards. The thermostat has 4 operation modes which can be controlled manually and
locally or through remote controlled through Zigbee gateway controller.
•
All setup is performed via supported IEEE 802.15.4-based control platforms and other Zigbee3.0 compatible
control systems. Appropriate gateway control software allows for adjustment of control mode, control type,
schedule etc.
•
Sensors: Air temperature
•
THERMOSTAT MODE: OFF, HEAT, ENERGY HEAT, AWAY, DRY
•
Measurement range: –10°C to +60°C
•
Accuracy: ±0.1°C
•
WARNING: Electrical power must be switched off during installation
2.4GHz
EU: AC200-240V, 50/60Hz
EU: AC200-240V
3680W @ 230V (resistive load)
16A
<2W
0°C to 40°C (during operation)
0°C to 40°C
0.5°C to 2°C (default 0.5°C)
Control Mode
OFF, HEAT, ENERGY HEAT
,
AWAY, DRY
Wiring Requirement
Current
≤
13A - 1.5mm² wire
Current > 13A to 16A - 2.5mm² wire
IP Rating
Control Pollution Degree (Method D)
Rated Impulse Voltage (Method D)
Relative Humidity
Dimensions
IP21
8% to 80%
4kV
80x80x52mm
pollution degree 2
Revised 11.08.2021
