background image

  

 

 

                                                                                

 

 

REFRESH® P HPDC – REFRESH® P TC 

REFRESH® Pensile 

Installation and Operation Manual 

 
Thank you for choosing a Zerica® water dispenser. 
Using the appliance is simple, however for best results, it is important to read the following instructions. 
 

(010) 

  
 

 
INTRODUCTION 

This manual is the documentation and an integral part of the appliance and must accompany the product even if it is 
transferred or sold after first installation. 
Its  disclosure  to  all  interested  parties  is  a  prerequisite  for  correct  operation  and  protection  from  possible  accidents 
and damage to the appliance and injury to third parties. 
These instructions are intended to provide information regarding correct installation and operation. 
The presence of such warnings does not imply that the manufacturer assumes any liability for any damage to property 
or injury to third parties caused by the use of the device, which has all the original certifications required in order to 
make it suitable for the use for which it has been designed, as well as safe in compliance with applicable standards. 
The  reproduction  of  the  contents  of  this  manual  for  distribution  to  third  parties  is  strictly  forbidden  without  the 
express prior consent of the manufacturer Zerica S.r.l. 
 
This  appliance  is  not  intended  for  use  by  persons  (including  children)  with  reduced  physical,  sensory  or  mental 
capabilities, or lack of experience and knowledge, unless they have been given supervision or instructions concerning 
the use of the appliance by a person responsible for their safety. Children must be supervised to assure that they do 
not play with the machine. 
 
The appliance must not be installed near water jets. 
The appliance needs to be installed on a flat surface. 
The appliance must not be cleaned with water jets. 
The appliance is compliant  with the N climate class and must  be installed in locations  with a  temperature between 
+16°C  and  +32°C.  Take  all  necessary  precautions  and  do  not  install  in  locations  with  temperatures  lower  than  +3°C 
because if the water inside the product freezes, it seriously damages the water circuit. 
This appliance generates a sound pressure level below 70dB. 
 

(020) 

 
 
 

Summary of Contents for REFRESH P HPDC














Reviews: