background image

1. Read this manual carefully until you

completely understand and can follow all
safety notes, precautions, and operating
instructions before using of the unit. 

2. Do not operate this tool when you are tired,

ill, or under the influence of alchohol, drugs,
or medication. 

3. Always wear eye or face protection and

hearing protection. 

4. Do not wear loose clothing, jewelry, short

trousers, sandals, or go barefoot. Do not
wear anything which might be caught by
branches or moving part of the unit. Secure
hair so it is above shoulder length. 

5. Never start or run the engine inside a

closed room or building. Exhaust gases
contain dangerous carbon monoxide. 

6. Before starting the engine, inspect the

entire unit for loose fasteners and fuel
leakage. Make sure that the cutting
attachment is properly installed and
securely fastened. 

7. Be sure the blade guard is attached in

place. 

8. Fuel is highly flammable. Always keep open

flames and sparks away from the unit and
fuel depot. Do not smoke while refueling the
unit or mixing fuel. 

9. When refueling the unit, make sure to stop

the engine and allow it to cool down. Wipe
spilled fuel completely from the unit. Move

848JL493A2 (704)

OWNER’S  MANUAL

1

2

(1) Read the owner's manual. 
(2) Wear a helmet, ear protection and eye

protection. 

(3) Warning / Attention 
(4) Keep all children, bystanders and helpers

15 meters away from the brushcutter. 

Explanation of pictorials 

at least 3 meters away from fueling site
before starting the engine. 

10.Check the condition of working area to

avoid any accident by hitting hidden
obstacles such as stumps, stones, cans, or
broken grass. 

11.Keep bystanders and animals at least 15

meters away from the operating point, If you
are approached, immediately stop the
engine. 

12.Keep firm footholds and balance at all

times. Do not use the unit where footing is
unsteady or slippery. 

13.Keep cutting attachment below waist level. 
14.Keep all parts of your body away from the

rotating cutting attachment and hot
surfaces. 

15.Warn the operator of the danger of blade

thrust. (Kick back) 
Blade thrust may occur when the spinning
blade contacts a solid object in the critical
area. A dangerous reaction may occur
causing the entire unit and operator to be
thrust violently. This reaction is called Kick
back. As a result, the operator can lose
control of the unit which can cause serious
or fatal injury. Kick back is more likely to
occur in areas where it is difficult to see the
material to be cut. 

16.When inspecting or servicing the unit, make

sure to stop the engine and disconnect the
spark plug as necessary. 

17.Cover the blade when the transporting or

storing the unit. Secure the unit before for

storage or transporting to prevent loss of
fuel, damage or injury. 

18.When replacing cutting attachment or other

components, be sure to use the parts
supplied or recommended by ZENOAH. 

19.When the unit is turned off, make sure the

cutting attachment has stopped before the
unit is set down. 

20.For units equipped with a clutch, be sure

the cutting attachment stops turning when
the engine idles. 

21.Use only for tasks explained in the

instruction handbook. 

22.Discard blades that are bent, warped,

cracked, broken or damaged in any way. 

23.Instructions on stopping a coasting blade. 

A blade can injure while it continues to spin
after the engine is stopped or throttle control
is released. 

24.Stop the engine and blade before removing

material that is blocking or entangling the
cutting attachment. 

25.Use a sharp blade. A dull blade is more

likely to snag and thrust. Replace the
fastening nut according to the
manufacturer's instruction. 

26.Cut only material recommended by the

manufacturer. Do not let the blade contact
material it cannot cut, such as rocks, metal
etc. 

27.Always wear safety boots, additionally a

helmet is required if there is a risk of contact
with falling objects. 

For safe operation

Thank you for purchasing a ZENOAH product.
Before using our brushcutter, please read this manual carefully
to understand the proper use of your unit.

1-9 Minamidai, Kawagoe, Saitama, 350-1165 Japan 

BRUSHCUTTERS

BC2310LE
BC2610LE/WE
BC3500LE/WE
BC4500WE
BC530WE

Summary of Contents for BC2310LE

Page 1: ... and hot surfaces 15 Warn the operator of the danger of blade thrust Kick back Blade thrust may occur when the spinning blade contacts a solid object in the critical area A dangerous reaction may occur causing the entire unit and operator to be thrust violently This reaction is called Kick back As a result the operator can lose control of the unit which can cause serious or fatal injury Kick back ...

Page 2: ...he quantities of gasoline and oil to be mixed 2 Put some of the gasoline into a clean approved fuel container 3 Pour in all of the oil and agitate well 4 Pour In the rest of gasoline and agitate again for at least one minute As some oils may be difficult to agitate depending on oil ingredients sufficient agitation is necessary for the engine to last long Be careful that if the agitation is insuffi...

Page 3: ...spool is capable for a line upto 6 m on the 4 head Avoid using a larger line as it may cut down the trimming performance 2 Pinch the slotted area on the both sides of the spool housing to unhook the bottom cap 3 Take out the spool and pull off the old line Put one end of new line through the spool holes and pull it until the length is equal between each part of the line 4 Wind up the line in the c...

Page 4: ...ndle type Loop Both Loop Both Throttle lever Trigger Type With Safety lock Standard cutter Nylon Harness type Single Double Quick release Yes Standard accessories Goggle Tool kit Owner s manual Specifications are subject to change without notice Specifications MAINTENANCE BEFORE STORAGE Old fuel left in the carburetor may cause starting failure When a series of operation finished make sure to empt...

Reviews: