background image

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Installation  

Programming Manual 

EVM2010A   

EVM2006A  

MN1000920E

Auto Attendant System 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Table of Contents 

1.  Call Processing Flow Chart

 ----------------   1 

2. Installation 

System Layout - ----------------------------------------- 3 
Installation Procedures -------------------------------- 5 

3.  Voice Instruction Menu 

System Program -----------------------------------------  7 
Administrator Program ---------------------------------  9 
Mailbox Owner Program -------------------------------   11 

4.  Program Explanations and Examples 

Voice Message Recording ----------------------------  13 
Extension Number Groups ----------------------------  15 
Operator Number ----------------------------------------  17 
Identification Code -------------------------------------- 19 
Message Notification -----------------------------------  21 
Information Menus --------------------------------------  23 
Other Functions ------------------------------------------  25 

5. Appendix 

Troubleshooting ------------------------------------------   27 
Reference data for PBXs ------------------------------  29 
User Information Form ---------------------------------  30 

Summary of Contents for Auto-Attendant System


















Reviews: