![background image](http://html1.mh-extra.com/html/yin-yan-model-tech/emax-series/emax-series_user-instruction_910481001.webp)
E
MAX YIN YAN MODEL TECH.MFT.
User Instruction for R/C Model Car ESC
Specification
Battery Cell
Item
Continuous
current
Li-XX Ni-Mh
/Ni-Cd
Dimension
(mm)
L×W×H
Weight
(
g
)
BEC
Program
By
key
EMAX-6A
6A
1-2
3-8
12 x 20 x 5
4
1A/5V
NO
EMAX -10A
10A
1-2
3-8
22 x 17 x 7
8
1A/5V
NO
EMAX -30A
30A
2-3
4-9
45x32x20
50
2A/5V
Yes
EMAX -45A
45A
2-3
4-12
45x32x20
50
2A/5V
Yes
EMAX -60A
60A
2-4
4-15
47x41x29
80
2A/5V
Yes
EMAX -80A
80A
2-4
4-15
47x41x29
80
2A/5V
Yes
EMAX -120A
120A
2-4
4-15
47x41x29
80
2A/5V
Yes
EMAX -150A
150A
2-6
5-18
96x55x21
180
0.2A/5V
NO
EMAX -120A-HV
120A
2-10
5-30
96x55x21
180
0.2A/5V
NO
Features
z
Full protection features including low voltage, over-heat, throttle signal loss, startup protection and self-check.
z
Compatible with sensor-free brushless motors.
z
Excellent startup performance, great throttle linear and quick throttle response.
z
Support highest motor speed 240,000RPM (2 poles), 80,000RPM (6 poles) and 40,000RPM (12 poles).
z
The parameters of ESC can be configured via pressing the keys.
z
System can automatically detect throttle neutral point and neutral range is adjustable.
z
Three working modes can meet different requirements.
z
4 steps of maximum reverse force adjustment, 5 steps of maximum start force adjustment.
z
3 steps of maximum brake force adjustment, 5 steps of drag brake force adjustment, 4 steps of initial brake force adjustment.
z
Support 1 cell operation (min voltage: 3V, only available for EMAX-6A and EMAX-10A).
Note: For EMAX-150A and EMAX-120A-HV, an UBEC or individual battery pack is required to power the receiver and
servos, and the red line (+5V) in 3 pin must be pulled out!
Instructions
Normal Startup Procedure
Move throttle stick to the neutral position
→
Switch on the transmitter
→
Connect battery pack to ESC
→
System detects the
neutral throttle signal, makes
a long
“
beep-
” sound
→
System detects battery voltage and makes several short “
beep-
” sounds,
which denotes the number of battery cells
→
when self-test is finished
→
“
♪
1 2 3
”
tone should be emitted
→
ready for start.
Setting Throttle Range
(Throttle range should be setup when a new transmitter is being used)
Switch off the ESC
→
Switch on the transmitter
→
Press and hold the “
SET ”
key
→
Switch on the ESC
→
Push the
throttle stick to the top point of forward within two seconds
→
wait for one second
→
System detects the Max throttle signal, and
makes two “
beep-
” sounds, which denotes that Max throttle has been confirmed and saved
→
Pull the throttle stick to the top point
of backward
→
System detects the Min throttle signal, makes two “
beep-
” sounds, which denotes that Min throttle has been
1