Yardistry Structures- Collection Series CS008
Fig. 4
(2.54cm)
Fig. 3- Pre-Drill Hole with 1/8” Drill Bit.
Cut Rail
1/8” Drill
Hole
5. Using a 1/8” drill bit, pre-drill Post and Rails in locations indicated by
the
arrows
and attach to side posts using 2 3/4” screws. (Fig.4)
*If you purchased the Post Stake to secure your project, please refer to the
instructions provided with the post stake to anchor your project to the ground.
B.
niveau que le panneau adjacent.
panneau vers le bas jusqu'à ce qu'il soit au même
pièces de raccordement femelles. Faites glisser le
Assemblez les panneaux côte à côte.
Conecte los paneles lado a lado.
Assemble Panels side by side. (Maximum 3 wide x 3 high)
Insérez les pièces de raccordement mâles dans les
Insert male into female. Slide down until flush with
adjacent panel.
Introduzca el extremo macho en el extremo hembra.
Deslícelo hacia abajo hasta que quede al ras del
panel adyacente.
*Les vis sons 2 1/4po
fourniers avec
poteau/Rail
2 x 2 x 62po.
C.
Screws* are 2 1/4"
included with
2x2x62" post/rail.
*Use los tornillos de
acero inoxidable
de 2 1/4" que se
incluyen en el
juego de
postes/travesaños
de 2x2x62".
Remove the male connectors from the outside of the
panel assembly.
Quite los conectores masculinos del exterior de la
asamblea de panel.
Enlever les connecteurs mâles de l'extérieur de
l'assemblée de panneau.
le connecteur
mâle court
connector
conector
masculino
short male
corto
male
connector
conector
masculino
connecteur
mâle
2 1/4” Screw
Drill Hole on an Angle
Thick Piece
of Wood
Skinny Piece
of Wood
Groove
Fig. 5
Screw on Backside
Screw on Backside
2 x One High X Topper | 2 x Arch Topper
2x -2”x2”x62” Post/Rail
Fig. 1
Fig. 2
2. Cut Posts and Rails to size indicated. (Fig. 2)
Circles and Triangles indicate at 45° cut.
(Use a
Mitre Box or Mitre Saw)
3. Where indicated by a triangle, use a 1/8” drill bit
to pre-drill a hole into the center of the 2x2 Rail.
(Fig.3)
4. Attach Post and Rails to panels with 2 1/4”
screws in locations indicated by
circles
using
pre-drilled holes where available. (Fig.4) When
pre-drilled holes are not available use a 1/8”
drill bit to drill holes on an angle in the inside of
the panel as shown. (Fig. 5)
1. Assemble panel in configuration shown.
(Fig. 1) Secure with 2 1/4” screws provided
in the direction and location of the arrows.
Use pre-drilled holes when available.
*Ensure Panels are oriented correctly!
(Fig. 1A)
Top View - Note:
Circles and
Triangles indicate a
45° cut.
8 11/16”
8 11/16”
Fig. 1A - Filler Strips on Bottom
of Panel!
Pilot holes to the right
Finished Project
(22.1cm)
(22.1cm)
(49.5cm)
(49.5cm)
(80.0cm)
(80.0cm)
(111.8cm)
2’ 7 1/2”
2’ 7 1/2”
Center the
Panels on
Posts and
Rails before
attaching!
YM11528
