DTX750K
Assembly Manual
This pamphlet describes the standard procedure for DTX750K assembly.
After assembling the parts and connecting the cords as shown below, you will be ready to turn on the drum trigger module.
• For assembly, you will require four individual packages – an RS700
Rack System, a DTP750C Pad Set, a DTP750P Pad Set, and a
DTX700 Drum Trigger Module.
• This pamphlet describes how to attach the pads and drum trigger
module to the RS700 Rack System. Before carrying out the proce-
dures described below, ensure that you have correctly assembled
the rack system as described in its assembly manual.
Before starting assembly, lay a drum mat (sold separately) on the floor.
Alternatively, before setting up the HS650A Hi-hat Stand and KP65
Kick Pad, you can place the packages' cardboard boxes on the floor to
protect it from damage
Before using, please read this assembly manual, and use this product in a safe and proper manner.
* Please keep this manual in a safe place for future reference.
* Make sure to read the Assembly Manual of the Rack System and the Owner’s Manual of the Pad.
NOTICE
• Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also,
never place any heavy or sharp objects on the cable. Applying excessive force to the cable may
result in damage to the cable, such as the wires being severed, etc.
• Do not step on or place heavy objects on the product. It may result in damage.
• Do not use or keep the product in places with extremely high temperature (places in direct sunlight,
close to a heater, in a closed car, etc.) or high humidity (bathroom, outside on a rainy day, etc.).
Doing so may result in deformation, discoloration, damage or deterioration.
• When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or
deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the
product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has
been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to
let the water and detergent come into contact with the cushions used in the product; doing so may
result in deterioration.
* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at
any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.
EN
PRECAUTIONS
Standard Assembly Example
PCY135
(Cymbal Pad)
PCY155
(Cymbal Pad)
CH750
(Cymbal Holder)
PCY135
(Cymbal Pad)
CH755
(Cymbal Holder)
XP80
(Tom Pad)
XP80
(Tom Pad)
KP65
(Kick Pad)
XP100SD
(Snare Pad)
SS662
(Snare Stand)
HS650
(Hi-hat Stand)
DTX700 Drum
Trigger Module
RHH135
(Real Hi-hat Pad)
CH750
(Cymbal Holder)
RS700
(Rack System)
IMPORTANT
NOTICE
If this symbol is ignored and the equipment is used improperly,
fatal injury to persons or serious damage could occur.
• Do not let small children assemble or set up this product by themselves, or they may be injured.
Always assemble this product with adult supervision.
• Be careful with the edges of the Cymbal Holders and the Tom Holders. The sharp holder ends
may result in injury.
• Be careful with the edges of the spurs attached to the Kick Pad and foot pedal. The sharp ends
may result in injury.
• If this product is used with a Rack System or Cymbal Stand, make sure all bolts are tightened
firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may
result in the rack overturning or parts dropping, causing injury.
• Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on
steps may result in the product being unstable and subject to overturning.
• When setting up the product, please pay close attention to the handling and setting of cables.
Carelessly placed cables may cause the user and others to trip and fall.
• Do not alter the product. Doing so may result in injury or damage/deterioration to the product.
• Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury.
If this symbol is ignored and the equipment is used improperly,
there is a danger or injury to persons handling the equipment, and
material damage could occur.
• Watch your fingers when adjusting clamps. They may become pinched, resulting in injury.
• Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your
fingers.
• Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting
in injury.
• Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums
may drop, causing injury.
Digital Musical Instruments Division
Digital Musical Instruments Division
©2011 Yamaha Corporation
WW60710 103PO***.*01B0
WARNING
CAUTION
Assemble the RS700 Rack System.
For details, refer to the assembly manual that came with the rack system.
Check the contents of each package.
Mount the pads and the drum trigger module on the rack system.
As described below, mount the pads and the trigger module on the rack system, and then position the kick pad and the hi-hat.
1
2
PCY135
Cymbal Pad (x2)
PCY155
Cymbal Pad (x1)
RHH135
Real Hi-hat Pad (x1)
Package 1: DTP750C
Package 2: DTP750P
Package 3: DTX700
Stand base for the
RHH135 (x1)
CH750
Cymbal Holder (x2)
CH755
Cymbal Holder (x1)
HS650A
Hi-hat Stand (x1)
Hi-hat clutch for the
RHH135 (x1)
Cable band for the
RHH135 (x1)
Stoppers for the
PCY135 and
PCY155 (x3)
Felts for the
PCY135 and
PCY155 (x3)
10-channel snake cable (x1)
PCY100, PCY135, and PCY155 Owner’s Manual (x1)
RHH135 Owner’s Manual (x1)
Assembly Manual (this pamphlet)
Tuning key (x1)
Cable band (x10)
DTX700 Owner’s Manual (x1)
DTX700 Data List (x1)
DVD (containing software)
DTX700 Drum Trigger
Module (x1)
AC power adaptor*
(x1)
Module stand (x1)
Module stand
fastening screws (x4)
XP100SD
Snare Pad (x1)
XP80
Tom Pad (x3)
SS662
Snare Stand (x1)
Clamp bolts (x4)
Clamp bolt small (x1)
KP65
Kick Pad (x1)
XP100T, XP100SD, XP120T, and XP120SD Owner’s Manual (x1)
XP70 and XP80 Owner’s Manual (x1)
KP65 Owner’s Manual (x1)
* May not be included de-
pending on your particular
area. Please check with
your Yamaha dealer.
3
Mounting the cymbal holders
Mounting the tom pad
1.
Mount the cymbal holders (CH750 x 2, CH755 x 1) on
the rack system as shown below.
CH750
CH750
CH755
1.
Attach the clamp bolt to each of the tom pads
and provisionally tighten (by 5 or 6 turns).
2.
Mount the tom pads on the rack’s clamp rods.
As shown below, ensure that the rod section
is fully inserted into each pad’s mounting hole,
and then fully tighten the clamp bolt.
3.
If necessary, use clamp bolts A to E to adjust
the height and angle of any of the pads. When
doing so, be sure to adjust one bolt at a time
(i.e., loosen a bolt, adjust the pad, and then
retighten before loosening another).
XP80
Clamp bolt (to be tight-
ened in the direction
shown)
Tom pad (rear side)
Tom pad
Rod
section
Clamp bolt
Insert
Clamp rod
Clamp bolt B
Clamp bolt D
Clamp bolt E
Clamp bolt A
Clamp bolt C
Continued on other side
dtx750k_en_0325.fm Page 1 Friday, March 25, 2011 11:01 AM
