background image

DocuColor 5252 System Administration Guide

12

2-1

2 T

o

o

ls M

ode

2.

Tools Mode

Key point:

Some features or options described in this chapter 

may not display or be selectable depending on the configuration of 
your machine.

Overview

The Tools Mode enables you to establish the default settings for 
your digital press, with or without a scanner, to fit your individual 
requirements. You can change the settings for a variety of 
features, such as the initial screen to display when the press is 
powered on, the language to display on the Touch Screen, special 
paper sizes that can be used in certain Paper Trays, timers, audio 
tone controls, default settings for scanner features, image quality 
settings, and more.

Entering and exiting Tools Mode

Key points:

If you attempt to access the Tools Mode while a job is printing, 
access to the screens will be delayed until the job completes 
printing.

Jobs will queue, but will not print while the Tools Mode is 
active.

You cannot access the Tools Mode if the digital press is in a 
Fault condition.

You cannot access the Tools Mode if the Pause key on the 
Control Panel has been pressed to halt a job. When the job 
that was stopped has been completed, Tools Mode may be 
accessed.

Summary of Contents for DocuColor 5252













































































































Reviews: