background image

 

1 / 11 

 

 

Note: 

On the cover sheet you can find warning information, and an explanation 
of

and 

symbols

 

the

 

terms used, together with the exclusion of liability. 

 

Contents

 

General ........................................................................................................................... 2

 

Code length / silent alarm ............................................................................................ 2

 

Battery ......................................................................................................................... 2

 

Interfaces .................................................................................................................... 2

 

Du delay time ................................................................................................. 2

 

Penalty time ................................................................................................................. 2

 

Overview of user rights ................................................................................................ 3

 

Open ............................................................................................................................... 3

 

Opening with Dualcode ................................................................................................... 3

 

Opening with active delay time ........................................................................................ 4

 

Triggering a silent alarm .................................................................................................. 4

 

Menu functions ................................................................................................................ 5

 

0 Change code ............................................................................................................ 5

 

1 Create user ............................................................................................................... 5

 

2 Blockade .................................................................................................................. 6

 

3 Delete user ............................................................................................................... 6

 

5 Check system ........................................................................................................... 6

 

6 System setup ............................................................................................................ 7

 

6-1-1 Mode change UART, serial communication .................................................... 7

 

6-1-2 Switch off analog keypad ................................................................................ 7

 

6-1-3 Activating the analog keypad and UART ........................................................ 8

 

6-2 Configuration of silent alarm .............................................................................. 8

 

6-3 Activate / deactivate external system blockade .................................................. 9

 

6-4 (De)Activate Dualcode ....................................................................................... 9

 

6-5 Battery warning threshold .................................................................................. 9

 

7 Overview of users ................................................................................................... 10

 

8 Activate setup mode ............................................................................................... 10

 

9 Set delay ................................................................................................................ 11

 

 

 

Operator

Instructions

 

administrators

 

user

 

and

 

system

 

for

 

 

Manual

 

 

4000

Wittkopp

 

Anchor

 

Summary of Contents for ANCHOR












Reviews: