1.
For safety sake, check first if your ignition key can activate engine start while the hand gear is engaged. If
engine starting can be done if hand gear is engaged, set gear mode in “manual hand gear mode” during
installation (Refer to the operation guide.)
2.
Check if immobilization feature is present in your automobile. If so, another accessory (Item no: 444) is
required to enable remote engine start. This accessory can be bought from the same dealer.
3. Check the circuits and their current first. Refer to [Installation diagram for input/ output current values]. If
the output current is lower than the requirement, additional relays must be added.]
※
check the following after installation of alarm system
1.
Installation is abnormal if the remote engine start can be done under these conditions (a) the gear is
engaged 9b) ignition key is in “ Ignition ON Mode” (c) the engine hood is open (D) the hand brake is not
engaged.
2.
The remote control should control operation of function is the same way as the original key .If remote
control can hardly remote engine start, the installation is abnormal. Check the related circuit connection of
the ignition cylinder.
3. For servicing, repair and valet parking, “Valet mode” must be set to “ON”.
Remote control features
【 】【
】
【
】【 】【 】
1.
Remote door lock/arm
To remote door lock, press and release
】
button after closing the door;: siren chirps once with one
parking light flash.
l
The remote transmitter sound 1 buzz and its LCD display locked icon
.
【
It remote transmitter sound 4
buzzes , the system is not working normally
】
.
2.
Remote door unlock/disarm
To remote the locked door, press and release
【
】
; siren chirps twice with 2 parking light flashes .
l
The remote transmitter sounds 2 buzzes and its LCD show unlock icon
2 stages door unlock /disarm
【
Refer to #36, Program table 1
】
Another accessory [1xxx] buyable from the same dealer is required .After setting the system at 2
stage door unlock, a press on button
【
】
can unlock driver’s door and longer press on the same
button can unlock all other others. Siren chirps 2 times with 2 parking light flashes.
l
The remote transmitter sounds 2 buzzes and its LCD shows unlock icon
Single
Option
(Choose
One
only)
Activate channel # 3
【
Refer to # 36, Features program table 1
】
The system must be set at Channel # 3 mode. Press and hold
【
】
.The system responds according
to its mode setting with 3 parking light flashes.
l
The remote transmitter sounds 3 buzzes and its LCD shows unlock icon
3.
Security diagnostic report
If there is \unlock/ disarm command received by the main system under lock/ arm mode; the main system
will still remain in the arm mode. If any intrusion is attempted, the siren will chirps 4 times with 4 parking
light flashes. The remote transmitter sounds 4 buzzes and its LCD will display the attempted zones.
4.
Remote engine start
To remote engine start
while the ignition “OFF”, press and release
【
】
; siren chirps 3 times with 3
parking light flashes. During starting process, the remote transmitter sounds melody and its LCD show
starting process, current status of the car.
l
The remote transmitter sounds melody with its LCD showing engine runs status. For runtime setup,
【
refer
to Program table at #36
】
. Engine run shuts off when the preset time expires. If the engine start fails, the
remote transmitter’s buzzer sounds 4 beeps twice.
5.
Remote activate engine run time
【
Refer to Remote transmitter’s functions table
】
Following the success of the engine start, each time press on
【
】
can automatically extend engine
runtime with 5 min step-up time. Maximum 20 min runtime can be attained. Engine shuts off
※
PRE-INSTALLATION CHECK
Model No. TR53A SUPER RANGE 2-WAY SECURITY
WITH REMOTE ENGINE START
