background image

30" (76.2 cm) Freestanding Electric Range

PRODUCT MODEL NUMBERS

PRODUCT DIMENSIONS

WFC110M0A
WFC120M0A
WFC130M0A
WFC150MLA
WFC310S0A
WFC340S0A
WFE320M0A

WFE330W0A
WFE510S0A
WFE520C0A
WFE524CLA
WFE524CLB 
WFE524WLA
WFE530C0A

WFE540H0A
WFE710H0A
WFE714HLA
WFE720H0A
WFI910H0A

Because Whirlpool Corporation policy includes a continuous commitment to improve our
products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.

Electrical:

To properly install your range, you must determine the type

of electrical connection you will be using and follow the instructions
provided for it here.

● 

Range must be connected to the proper electrical voltage and frequency
as specified on the model/serial number rating plate. The model/serial
number rating plate is located on the left side frame behind the storage
drawer panel or behind the top right side of the oven door. Refer to the
figures in the “Product Dimensions” section of the “Location
Requirements” section.

● 

This range is manufactured with the neutral terminal connected to the
cabinet. Use a 3-wire, UL listed, 40- or 50-amp power supply cord
(pigtail) (see following Range Rating chart). If local codes do not permit
ground through the neutral, use a 4-wire power supply cord rated at 
250 volts, 40 or 50 amps and investigated for use with ranges.

Range Rating* 

Specified Rating of
Power Supply Cord Kit
and Circuit Protection

120/240 Volts 

120/208 Volts 

Amps 

8.8 - 16.5 KW

7.8 - 12.5 KW

40 or 50**

16.6 - 22.5 KW

12.6 - 18.5 KW

50

*The NEC calculated load is less than the total connected load listed on

the model/serial rating plate.

**If connecting to a 50-amp circuit, use a 50-amp rated cord with

kit. For 50-amp rated cord kits, use kits that specify use with a
nominal 1

³⁄₈

" (34.9 mm) diameter connection opening.

● 

A circuit breaker is recommended.

CABINET OPENING DIMENSIONS

Ref. W10403811B

5/6/13

A. 27

³⁄₄

" (70.5 cm) max. depth with handle

B. 46

⁷⁄₈

" (119.1 cm) overall height (max.) with leveling legs 

screwed all the way in*

C. 36" (91.4 cm) cooktop height (max.) with leveling legs screwed 

all the way in*

D. 29

⁷⁄₈

" (75.9 cm) width

E. 25

⁵⁄₁₆

" (64.3 cm) depth - back of range to front of cooktop**

F. Model/serial rating plate (located on the left side frame behind 

storage drawer or right side of frame behind the oven door)

A

B

C

D

E

F

A. 13" (33.0 cm) max. upper cabinet depth
B. 30" (76.2 cm) min. opening width

C. For minimum clearance to top of cooktop, see NOTE*
D. 30

¹⁄₈

" (76.5 cm) min. opening width

E. Outlet - 8" (20.3 cm) to 22" (55.9 cm) from either cabinet,

5

¹⁄₂

" (14.0 cm) max. from floor

F. Cabinet door or hinges should not extend into the cutout

A

B

D

F

E

C

IMPORTANT:

Range must be level after installation. Follow the instructions

in the “Level Range” section. Using the cooktop as a reference for leveling
the range is not recommended.

*

*

Range can be raised approximately 1" (2.5 cm) by adjusting the leveling

legs.

**

Front of door and drawer may extend further forward depending on

styling.

Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth,
24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height.

IMPORTANT:

If installing a range hood or microwave hood combination

above the range, follow the range hood or microwave hood combination
installation instructions for dimensional clearances above the cooktop
surface.
A freestanding range may be installed next to combustible walls with zero
clearance.

*

NOTE: 

24" (61.0 cm) minimum when bottom of wood or metal cabinet is

covered by not less than 

¹⁄₄

" (0.64 cm) flame retardant millboard covered

with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel,

0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.

*

24" (61.0 cm) minimum when bottom of wood or metal cabinet is covered

by not less than 

¹⁄₄

" (0.64 cm) flame retardant millboard covered with not

less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024"

(0.6 mm) aluminum or 0.020" (0.5 mm) copper.

Reviews: