background image

www.whirlpoolcommerciallaundry.com

W10889132A
W10889135A – SP

TABLE OF CONTENTS

 

Page

Washer Safety .......................................................................... 2
Tools & Parts ............................................................................ 3
Dimensions .............................................................................. 4
Location Requirements ........................................................... 5
Drain System ............................................................................ 6
Electrical Requirements.......................................................... 7
Installation Instructions .......................................................... 8
Connect Drain Hose ................................................................ 9
Connect Inlet Hoses .............................................................. 10
Level Washer .......................................................................... 11
Installing Coin Slide and Coin Box ....................................... 11
Complete Installation ............................................................ 12
Typical Full Load Sizes .......................................................... 12
Washer Maintenance............................................................. 13
If You Need Assistance ......................................................... 14
Alternate Parts & Accessories ............................................. 14
Warranty ................................................................................. 15

TABLE DES MATIÈRES

 

    

Page

Sécurité de la laveuse ........................................................... 16
Outillage et pièces ................................................................. 17
Dimensions ............................................................................ 18
Exigences d’emplacement ................................................... 19
Système de vidange .............................................................. 20
Spécifications électriques .................................................... 21
Instructions d’installation ..................................................... 22
Raccordement du tuyau de vidange .................................... 23
Raccordement des tuyaux d’arrivée d’eau ......................... 24
Établissement de l’aplomb de la laveuse ............................ 25
Installation de la glissière et de la boîte à monnaie ........... 25
Achever l’installation ............................................................. 26
Taille typique des charges complètes ................................. 26
Entretien de la laveuse .......................................................... 27
Si vous avez besoin d’assistance ........................................ 28
Pièces supplémentaires et accessoires .............................. 28
Garantie .................................................................................. 32

INSTALLATION

INSTRUCTIONS

Commercial Washer

INSTRUCTIONS 

D’INSTALLATION

Laveuse commerciale 

Summary of Contents for CAE2765FQ0
















Reviews: