1
1
BULL BAR ASSEMBLY
2,3
2
BRACKET, PASSENGER (2) AND DRIVER (3)
4
2
PLASTIC PLUG
5
4
RUBBER BUMPER
6
4
3/8-16 X 1.00” HEX HEAD BOLT
7
8
3/8” FLAT WASHER
8
4
3/8” LOCK WASHER
9
4
3/8-16 HEX NUT
1
1
ENSAMBLE DE PARRILLA DELANTERA CON TIRÓN
2,3
2
SOPORTE
4
2
TAPONES DE PLÁSTICO
5
4
PARACHOQUES DE HULE
6
4
PERNOS CON CABEZA HEXAGONAL DEL DE 3/8-16 x 1.00”
7
8
ARANDELAS PLANAS DE 3/8”
8
4
ARANDELAS DE PRESIÓN DE 3/8”
9
4
TUERCAS HEXAGONALES DE 3/8-16
, LADO DEL ACOMPAÑANTE
Y EL CONDUCTOR
(2)
(3)
1
1
LA BULL BAR
2,3
2
SUPPORT, PASSAGER (2) ET CONDUCTEUR (3)
4
2
BOUCHONS DE PLASTIQUE
5
4
PARE-CHOCS CAOUTCHOUC
6
4
BOULONS A TETE HEXAGONALE 3/8-16 X 1,00 PO
7
8
RONDELLES PLATES 3/8 PO
8
4
RONDELLES A FREIN 3/8 PO
9
4
ÉCROUS HEXAGONAUX 3/8-16
QTY
CONTENTS -
CONTENIDO
- CONTENU
TOOLS -
HERRAMIENTA
- OUTILS
9/16” SOCKET
15/16” SOCKET
15/16” WRENCH
9/16” WRENCH
18MM SOCKET
RATCHET
TORQUE WRENCH
APPLICATION: 2006-08 HUMMER H3
ITEM
APLICACIÓN:
, MOD. 2006-08
HUMMER H3
APPLICATION:
2006-08
HUMMER H3
AUTOMOTIVE PRODUCTS, INC.
DADO DE 9/16”
LLAVE DE TUERCAS DE 9/16”
DADO DE 5/16”
LLAVE DE TUERCAS DE 5/16”
DADO DE 18 MM
MANERAL
LLAVE DE TORQUE
DOUILLE 9/16 PO
CLE 9/16 PO
DOUILLE 5/16 PO
CLE 5/16 PO
DOUILLE 18MM
CLIQUET
CLE DE COUPLEB
BULL BAR ASSEMBLY
ENSAMBLE DE PARRILLA
DELANTERA CON TIRÓN
LA BULL BAR
33-1920
33-1925
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
STEP 1.
STEP 2.
STEP 3.
STEP 4.
STEP 5.
STEP 6.
Remove the contents from box and check for damage. Verify all parts are present. Read instructions
completely before beginning.
Westin advises the installer to use a thread lubricant on all of the
stainless steel fasteners.
It may be necessary to remove/relocate front license plate and license plate bracket. It is not
required, but strongly recommended. If local/state laws requires a license plate, license plate relocation kit
32-0055 is available.
Determine passenger and driver brackets.
Locate tow hook loops on the front bumper. Remove the nut and bolt holding the tow hook loop to the tow
hook bracket. The tow hook loops will not be reinstalled. Remove the two 12mm bolts that hold the tow
hook brackets to the bumper.
Do not remove tow hook bracket.
Position Bull Bar mount brackets over top of tow hook mount bracket. Reinstall factory 12mm bolts. Leave
loose.
Make sure Bull Bar and brackets are
properly aligned and tighten all fasteners. Recommended torque values are 37 Ft. Lbs. for M12 bolts and
17 Ft.Lbs. for 3/8” stainless steel fasteners.
Insert threaded stud on base of the light through hole in cross tube. Using a ratchet, extension
and socket for correct size of nut supplied, insert through large clearance hole in bottom of cross tube.
NOTE:
NOTE:
SEE FIGURE 2.
NOTE:
SEE FIGURE 2.
SEE FIGURE 2.
LIGHT INSTALLATION:
Attach Bull Bar to mount brackets using 3/8” stainless steel fasteners.
75-0551 REVISION C 4/23/08
WO:
1
2
3
