![background image](http://html1.mh-extra.com/html/westek/lpl748w/lpl748w_owners-manual_959932001.webp)
Location of Controls
1. ON/OFF Switch with Selectable Dimmer
2. Adjustable Light Head
3. Battery Compartment*
4. Mounting Bracket
*On bottom of unit.
Installation
Hook and Loop Tape (included)
NOTE:
Hook and loop tape may be cut to desired size for easier removal.
1. Check the location of where you want to place the spotlight.
Make sure it is clean and there is no debris or dust.
2. Remove the paper covering to expose one sticky side of the tape.
3. Place the hook and loop tape in the recessed area on the mounting bracket.
4. Remove the paper covering on the other side of the tape to expose the sticky surface.
5. Place the spotlight in the desired location. Press fi rmly for fi ve (5) seconds so the tape adheres to the surface.
CAUTION:
Be cautious of what surface the hook and loop adhesive is attached to, as it may remove paint or
damage surface.
Detachable Bracket and Screws (included)
1. Remove the hook and loop tape by pulling the tape away from the mounting bracket.
2. Remove the printed mounting bracket template to use as a guide. Drill two (2) pilot holes in the location where
you want to mount the spotlight.
3. Remove the mounting bracket so it can be mounted. To do so, hold the spotlight base in one hand, with the
mounting bracket facing up. With the other hand grab fi nger grips (Fig. 1) on mounting bracket and pull away
from the spotlight. The cover will pop off. You may also use a fl athead screwdriver to gently pry off the mounting
bracket.
NOTE:
It may help to turn the spotlight base clockwise or counter-clockwise as you are pulling it off.
4. Place screws (included) in pre-drilled holes. Tighten slightly until secure, but do not tighten all the way.
Align and slide the keyhole slots on the mounting bracket over screw heads. Slide the bracket so the narrow
ends of the keyhole slots are under the screw heads. Tighten screws to secure mounting bracket to mount-
ing surface. Take care to not over tighten.
5. Re-attach the spotlight to the detachable bracket. It will snap into place.
NOTE:
The base of the spotlight also acts as a stand so it can be placed on desk tops, table tops, just about
anywhere!
Operating Directions
Universal Light Positioning
Unique light head is fully adjustable. It can be rotated 330° left or right as well as pivoted 160° up and down
for the desired light positions.
NOTE:
The light head can only be pivoted 160° up and down (Fig 1) or turned 330° left or right (Fig 2). To prevent
damage to the unit, do NOT overturn the light heads. Doing so may damage the unit and will void the warranty.
ON/OFF/DIMMER Operation
• Press once for full brightness.
• Press and hold until the LEDs reach the desired brightness then release the button.
• Press a third time to turn the light OFF.
Inserting/Replacing the Batteries
If the LEDs appear to be dim this is an indication that your batteries need to be replaced.
1. Remove battery compartment cover on the back of the spotlight light head. To do so, hold the front of the spotlight
in one hand, with the other hand twist the battery cover counter clockwise
(in the direction of the “OPEN” arrow) and pull off.
2. Install three new AA batteries.
3. Make sure to follow battery polarity guide when installing new batteries.
4. Replace battery compartment cover by placing it back on the spotlight making sure that the “Open” and “Lock”
markings are at the top of the spotlight (Fig. 1). Twist it clockwise until it locks into position (in the direction of the
“LOCK” arrow).
Battery Precautions:
1. Use only the size and type of batteries specifi ed.
2. Always purchase the correct size and grade of battery most suitable for the intended use.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.
5. Replace all batteries of a set at the same time. Do not mix old and new batteries.
6. Clean the battery contacts and also those of the device prior to battery installation.
7. Do not dispose of batteries in fi re.
8. Remove batteries if consumed or if product is to be left unused for an extended period of time.
LPL748W/LPL748 Owner’s Manual
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING:
Modifi cations to this product not approved by the party responsible for compliance could void the user’s authority to operate the product.
One-Year Limited Warranty
AmerTac warrants to the original purchaser that this product will be free from defects in materials
and workmanship for a period of one year from the date of purchase. Additional details are
available at www.amertac.com. PROP. 65 WARNING: This product contains chemicals known to
the State of California to cause cancer and/or birth defects or other reproductive harm.
AmerTac
250 Boulder Dr.
Breinigsville, PA 18031
610-336-1330
www.amertac.com
Made in China
© 2017 AmerTac™
I17-0001-A
WIRELESS LED “SPOTLIGHT”
1
2
3
4
Hook and Loop
Tape Area
Keyhole
Slot
Keyhole
Slot
1/2” Gap
Fig 2
Fig 1
Tab
Light Base
Finger Grips